Vixel 335 manual Scsi

Page 72

Vixel Model 335 Installation & Configuration Guide

APPENDIX E Glossary

 

 

Non-overlapping

Enables the switch to be divided into separate environments,

Zones

where each environment sustains a complete 127-device AL_PA

 

space.

 

Open

An Arbitrated Loop protocol used to establish a switch circuit.

Overlapping

Devices on one port are not allowed to see devices on another

Zones

port, yet those same devices can both see a device on a third

 

port.

 

Protocol

A data transmission convention which may include timing,

 

control, formatting, error detection with correction and data

 

representation.

 

SCSI

Small Computer System Interface. Standard interface for storage

 

modules.

 

SFP

Small Form-Factor Pluggable transceiver. These transceivers are

 

fully compliant with the FC-PI and MSA standards and occupy

 

less than half the board space of the existing GBIC products.

SNMP

Simple Network Management Protocol. A protocol for

 

managing systems and devices in a network. Supports the

 

retrieving data, writing data, and setting traps indicating events.

Topology

The logical and/or physical arrangement of stations on a

 

network. Fibre Channel topologies include point-to-point,

 

Arbitrated Loop, and switched fabric.

Transceiver

A device that converts one form of signaling to another for both

 

transmission and reception. SFPs and GBICs are transceivers.

Zoning

Dividing a network into separate areas to group devices and

 

isolate traffic.

 

69

Image 72
Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Features IntroductionAbout This Guide OverviewFibre Channel Arbitrated Loop InSpeed TechnologyInstallation Unpacking the SwitchInstalling the Switch Using Small Form Factor Pluggable SFP Transceivers Performing a Power On Systems TestSmall Form-Factor Pluggable SFP Installation Small Form-Factor Pluggable SFP RemovalSetting Up the Switch Attaching DevicesUnderstanding the Switch’s LEDs Power OnSystem LEDs System LEDs Indication Port LEDsSFP Cascading Switches Cascading with Non-Overlapping ZonesAcceptable Single Cascade in Zones 2-12 Only Using the Web Manager Connecting to the Web ManagerE rv i e w Navigation Logging On and OffConfiguring the Switch Configuration Task Location in Web ManagerResetting the Switch System Information Settings Setting DescriptionNetwork Settings Click Change SettingsSwitch Speed Switching ModeSwitch Identification Blocking ARBDownloading the Switch Configuration Time SettingsFirmware Settings Firmware InformationClick Change Firmware Settings Event Log MessagesFC Switch Information FC Switch InformationOS Information Detection IndicationCLS Port Usage Information 11.Ordered Set Information Page with Highlighted ZonesValue Description 13.Received Port Utilization Page with Highlighted ZonesPort Settings 15.Port Information16.Port Information Page with Highlighted Zones Mode Description 18.Cascade Information19.Cascade Information Page with Highlighted Zones Policy Settings Switch Policy Description21.Policies Change Settings Zone Settings 22.Overlapping ZonesOverlapping Zones 25.Overlapping Zone 1 Information26.Overlapping Zone 1 Information Configuration Non-Overlapping ZonesClick Back to Non-overlapping Zone Info to view the changes Management Using the Command Line Interface CLI Connecting to the CLIConfiguration Task CLI Command NozChanging the Switch’s IP Parameters Configuring Switch InformationEnabling or Disabling Dhcp Requests Managing the Firmware Downloading New FirmwareMessage Action Configuring the Trap Destination Table Edit Trap Destination Menu Active Value NEW ValueOption Description Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies Policy DescriptionSettings Description Threshold InformationActions Action DescriptionChanging the Switching Mode Command DescriptionNumber. You can also change the port policies Displaying Ports PLLEnables you to configure control of the port. Select from Resetting the Switch Resetting the HardwareResetting the Switch to Factory Default Settings Viewing the Event LogChanging the Switch’s Operating Speed Overlapping Zoning ConfigurationViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10Reference Technical SupportTro ub l e sh oo ti n g Small Form-Factor Pluggable SFP Issues Fibre Channel ReferencesAppendixes Appendix a Specifications Specification sOperating Conditions Vixel Model 335 Operating ConditionsCommands Console CommandsGeneral Commands Browse CommandsAction Commands Show ZoneURL Appendix C Event Messages Event Meaning Action Severity MessageAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Configuring switch information IndexIndex
Related manuals
Manual 74 pages 62.9 Kb