Vixel 335 manual System Information Settings, Setting Description

Page 17

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

System Information Settings

The System Informations page displays the switch’s parameters and general configuration settings.

To view the system settings, click System. The System Information page appears.

Figure 3-2.System Information Page

The displayed settings are listed below:

Setting	Description

MAC Address	A unique device address assigned to each switch at the
	factory. Cannot be configured or modified.

Serial Num(ber)	A unique identification number assigned to each switch at the
	factory. Cannot be configured or modified.

IP Address	The current IP Address for the switch.

IP Gateway	The current Gateway address for the switch.

IP Netmask	The current IP Netmask address for the switch.

Speed	The current speed setting for the switch.

Speed Control (Last boot)	The speed setting selected during the last switch power-up.

Speed Control (Next boot)	The speed setting selected for the next switch power-up.

Switching Mode	When "on", allows data to be sent directly to a specified port.
	If "off", the data is sent to every port. Disabling Switching
	Mode may be necessary when passing data to legacy devices.

Blocking ARB	When two ports start a communication session, the Blocking
	ARB is sent to all other ports trying to communicate with
	those ports until the connection is terminated. Blocking ARB
	is only active when the switching mode is on.

14

Image 17

Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Introduction FeaturesAbout This Guide OverviewInSpeed Technology Fibre Channel Arbitrated LoopInstalling the Switch InstallationUnpacking the Switch Performing a Power On Systems Test Using Small Form Factor Pluggable SFP TransceiversSmall Form-Factor Pluggable SFP Installation Small Form-Factor Pluggable SFP RemovalAttaching Devices Setting Up the SwitchSystem LEDs Understanding the Switch’s LEDsPower On Port LEDs System LEDs IndicationSFP Cascading with Non-Overlapping Zones Cascading SwitchesAcceptable Single Cascade in Zones 2-12 Only E rv i e w Using the Web ManagerConnecting to the Web Manager Logging On and Off NavigationResetting the Switch Configuring the SwitchConfiguration Task Location in Web Manager Setting Description System Information SettingsClick Change Settings Network SettingsSwitching Mode Switch SpeedSwitch Identification Blocking ARBTime Settings Downloading the Switch ConfigurationFirmware Information Firmware SettingsEvent Log Messages Click Change Firmware SettingsFC Switch Information FC Switch InformationDetection Indication OS InformationCLS 11.Ordered Set Information Page with Highlighted Zones Port Usage Information13.Received Port Utilization Page with Highlighted Zones Value Description15.Port Information Port Settings16.Port Information Page with Highlighted Zones 18.Cascade Information Mode Description19.Cascade Information Page with Highlighted Zones Switch Policy Description Policy Settings21.Policies Change Settings 22.Overlapping Zones Zone Settings25.Overlapping Zone 1 Information Overlapping ZonesNon-Overlapping Zones 26.Overlapping Zone 1 Information ConfigurationClick Back to Non-overlapping Zone Info to view the changes Management Connecting to the CLI Using the Command Line Interface CLINoz Configuration Task CLI CommandEnabling or Disabling Dhcp Requests Changing the Switch’s IP ParametersConfiguring Switch Information Downloading New Firmware Managing the FirmwareMessage Action Edit Trap Destination Menu Active Value NEW Value Configuring the Trap Destination TableOption Description Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy Description PoliciesThreshold Information Settings DescriptionAction Description ActionsCommand Description Changing the Switching ModeNumber. You can also change the port policies PLL Displaying PortsEnables you to configure control of the port. Select from Resetting the Hardware Resetting the SwitchResetting the Switch to Factory Default Settings Viewing the Event LogViewing and Understanding Zoning Information Changing the Switch’s Operating SpeedOverlapping Zoning Configuration Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationTechnical Support ReferenceTro ub l e sh oo ti n g Fibre Channel References Small Form-Factor Pluggable SFP IssuesAppendixes Specification s Appendix a SpecificationsVixel Model 335 Operating Conditions Operating ConditionsConsole Commands CommandsGeneral Commands Browse CommandsShow Zone Action CommandsURL Event Meaning Action Severity Message Appendix C Event MessagesAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Index Configuring switch informationIndex

Related manuals

Manual 74 pages 62.9 Kb