Intelligent Motion Systems MDriveAC manual 76.2

Page 23

Mechanical Specifications

Dimensions in Inches (mm)

3.0

(76.2)

P1

P3

Connectors

Ø0.87 (Ø 22.1)

0.335

(8.51)

Ø 2.185 (Ø 55.5)

0.65

(16.51)

7.4

(187.96)

6.75

(171.45)

3.50SQ.

(88.88 SQ.)

P1 19-Pin M23

Ø0.87 (Ø 22.1)

P3 3-Pin Euro AC

Ø 0.75 (Ø 19.05)

0.83

(21.08)

4.50

(114.3)

0.1875

(4.76)

4.331 SQ.

(110.0 SQ.)

Control Knob

Ø1.90 (Ø 48.3)

LMAX2

LMAX

0.49

(12.5)

 

Dimensions in inches (mm)

Motor Length

LMAX1

LMAX2

 

(Single Shaft)

(Control Knob)

Single

7.4

(187.96)

9.4 (238.76)

Double

9.4

(2238.76)

11.4 (289.56)

2.17

(55.0)

1.375 (34.9)

0.75

(19.05)

0.059 (1.5)

Figure 1.4.1: MDrive42AC Plus Mechanical Specifications

Part 1: Hardware Specifications

1-17

Image 23
Contents 34 TM UL Application Details and Conditions of Acceptance Low Voltage Installation InformationTable Of Contents Appendices List Of Figures List of Tables Before You Begin Connecting AC PowerConnect Opto Power and Logic Inputs MDriveAC Plus MicrosteppingInstall the IMS SPI Motor Interface Connecting Parameter Setup CablePart Hardware Specifications Intentionally Left Blank Introduction to the MDrive34AC Plus Microstepping ConfiguringFeatures and Benefits Page General Specifications MDrive34AC Plus Microstepping Detailed SpecificationsSingle Length Setup ParametersDimensions in Inches mm Mechanical SpecificationsPin Assignment and Description P1 19-Pin M23 Connector I/O and SPI CommunicationsPin Assignment P1 I/O, SPI and Encoder Connections Pin Options and AccessoriesP3 Connector AC Power Introduction to the MDrive42AC Plus Microstepping Page MDrive42AC Plus Microstepping Detailed Specifications Setup Parameters 76.2 Pin Assignment and Description Pin Assignment P1 I/O, SPI and Encoder Connections Outside Pins 1 Options and Accessories Part Interfacing Configuring Intentionally Left Blank Optically Isolated Logic Inputs Isolated Logic Input Pins and ConnectionsLogic Interface and Connection Up/Down Step ClockDirection QuadratureChannel B DirectionStep Channel aOptocoupler Reference Optocoupler ReferenceOpen Collector Interface Example Input Connection ExamplesSwitch Fault Temperature Warning OutputSwitch Interface Example Minimum Required Connections 7 Fault Output interfaced to an LEDConnecting SPI Communications SPI Clock SPI Pins and ConnectionsSPI Master with Multiple MDriveAC Plus Microstepping Color Coded Parameter Values Using the IMS SPI Motor Interface InstallationConfiguration Parameters and Ranges View Motion Settings Screen Read-Only Part Serial Number ScreenIMS SPI Motor Interface Menu Options FileHelp UpgradeRecall Msel Microstep Resolution Selection Screen 1 The Motion Settings Configuration ScreenExit Connected/Disconnected IndicatorFactory SetInput Clock Filter Screen 2 I/O Settings Configuration ScreenEnable Active High/Low Input Clock TypeIMS IMS Serial Number Fault IndicationIMS Part Number/Serial Number Screen Upgrading the Firmware in the MDriveAC Plus Microstepping IMS SPI Upgrader ScreenUpgrade Instructions Port Menu Initialization ScreenCheck Sum Calculation for SPI Using User-Defined SPISPI Timing Notes MSB SPI Commands and ParametersSPI Communications Sequence WriteIntentionally Left Blank Appendices MDriveAC Plus Microstepping Hardware Revision R121707 Single Length MDriveAC Plus Microstepping Motor PerformanceMDrive34AC 120VAC MDrive34AC 240VACMDrive42AC 120VAC Double LengthTriple Length MDrive42AC Plus MicrosteppingOz-in/810 N-cm Selecting a Planetary Gearbox MDrive with Planetary GearboxSection Overview Product OverviewReduction Ratio Calculating the Shock Load Output Torque TABFactors Speed in Full Steps per Second Nominal Output Torque=1.6 =1.7 =1.9 Shock Load Output TorqueLead Screw System InertiaType of System Rack and Pinion Conveyor BeltBelt Drive Rotary TableFigure B.6 Chain Drive System Inertia Considerations Chain DrivePM81 Gearbox Ratios and Part Numbers Planetary Gearbox for MDrive34AC Plus2MDrive34AC Plus2 Planetary Gearbox Parameters PM105 Gearbox Ratios and Part Numbers Planetary Gearbox for MDrive42AC Plus2MDrive42AC Plus2 Planetary Gearbox Parameters PM105 PM120 Gearbox Ratios and Part Numbers MDrive42AC Plus2 Planetary Gearbox Parameters PM120Optional Cables and Cordsets MD-CC300-000 USB to SPI Parameter Setup CableInstallation Procedure for the MX-CC300-000 Installing the Cable/VCP DriversFigure C.4 Hardware Update Wizard Screen Determining the Virtual COM Port VCP Figure C.7 Hardware Update Wizard Finish InstallationTo Controller Interface AdapterMD-CS10x-000 Cordset Pin Assignment and Wire ColorsMD-CS201-000 MD-CS20x-000 CordsetFactory Mounted Encoder Pin ConfigurationInterfacing the Internal Differential Optical Encoder Differential Encoder Encoder SignalsSpeed-Force Limitations† FeaturesLinear Slide Option MDrive34Plus Linear SlideMechanical Specifications SpecificationsWarranty Excellence in Motion