Intelligent Motion Systems MDriveAC manual Part Interfacing Configuring

Page 28

Excellence in Motion TM

TM

mICROSTEPPING

PART 2:

INTERFACING AND

CONFIGURING

Section 2.1: Logic Interface and Connection

Section 2.2: Connecting SPI Communications

Section 2.3: Using the IMS SPI Motor Interface

Section 2.4: Using User-Defined SPI

Part 2: Interfacing and Configuring

2-1

Image 28
Contents 34 TM Low Voltage Installation Information UL Application Details and Conditions of AcceptanceTable Of Contents Appendices List Of Figures List of Tables Connecting AC Power Connect Opto Power and Logic InputsMDriveAC Plus Microstepping Before You BeginConnecting Parameter Setup Cable Install the IMS SPI Motor InterfacePart Hardware Specifications Intentionally Left Blank Features and Benefits ConfiguringIntroduction to the MDrive34AC Plus Microstepping Page MDrive34AC Plus Microstepping Detailed Specifications General SpecificationsSetup Parameters Single LengthMechanical Specifications Dimensions in Inches mmP1 19-Pin M23 Connector I/O and SPI Communications Pin Assignment and DescriptionPin Assignment P1 I/O, SPI and Encoder Connections P3 Connector AC Power Options and AccessoriesPin Introduction to the MDrive42AC Plus Microstepping Page MDrive42AC Plus Microstepping Detailed Specifications Setup Parameters 76.2 Pin Assignment and Description Pin Assignment P1 I/O, SPI and Encoder Connections Outside Pins 1 Options and Accessories Part Interfacing Configuring Intentionally Left Blank Logic Interface and Connection Isolated Logic Input Pins and ConnectionsOptically Isolated Logic Inputs Step Clock DirectionQuadrature Up/DownDirection StepChannel a Channel BOptocoupler Reference Optocoupler ReferenceInput Connection Examples Open Collector Interface ExampleSwitch Interface Example Fault Temperature Warning OutputSwitch 7 Fault Output interfaced to an LED Minimum Required ConnectionsConnecting SPI Communications SPI Master with Multiple MDriveAC Plus Microstepping SPI Pins and ConnectionsSPI Clock Configuration Parameters and Ranges Using the IMS SPI Motor Interface InstallationColor Coded Parameter Values Motion Settings Screen Read-Only Part Serial Number Screen IMS SPI Motor Interface Menu OptionsFile ViewRecall UpgradeHelp Screen 1 The Motion Settings Configuration Screen Msel Microstep Resolution SelectionConnected/Disconnected Indicator FactorySet ExitScreen 2 I/O Settings Configuration Screen Enable Active High/LowInput Clock Type Input Clock FilterIMS Part Number/Serial Number Screen Fault IndicationIMS IMS Serial Number Upgrade Instructions IMS SPI Upgrader ScreenUpgrading the Firmware in the MDriveAC Plus Microstepping Initialization Screen Port MenuSPI Timing Notes Using User-Defined SPICheck Sum Calculation for SPI SPI Commands and Parameters MSBWrite SPI Communications SequenceIntentionally Left Blank Appendices MDriveAC Plus Microstepping Hardware Revision R121707 MDriveAC Plus Microstepping Motor Performance MDrive34AC 120VACMDrive34AC 240VAC Single LengthDouble Length Triple LengthMDrive42AC Plus Microstepping MDrive42AC 120VACOz-in/810 N-cm MDrive with Planetary Gearbox Section OverviewProduct Overview Selecting a Planetary GearboxFactors Calculating the Shock Load Output Torque TABReduction Ratio Nominal Output Torque Speed in Full Steps per SecondShock Load Output Torque =1.6 =1.7 =1.9Type of System System InertiaLead Screw Conveyor Belt Rack and PinionRotary Table Belt DriveChain Drive Figure B.6 Chain Drive System Inertia ConsiderationsMDrive34AC Plus2 Planetary Gearbox Parameters Planetary Gearbox for MDrive34AC Plus2PM81 Gearbox Ratios and Part Numbers MDrive42AC Plus2 Planetary Gearbox Parameters PM105 Planetary Gearbox for MDrive42AC Plus2PM105 Gearbox Ratios and Part Numbers MDrive42AC Plus2 Planetary Gearbox Parameters PM120 PM120 Gearbox Ratios and Part NumbersMD-CC300-000 USB to SPI Parameter Setup Cable Installation Procedure for the MX-CC300-000Installing the Cable/VCP Drivers Optional Cables and CordsetsFigure C.4 Hardware Update Wizard Screen Figure C.7 Hardware Update Wizard Finish Installation Determining the Virtual COM Port VCPAdapter To Controller InterfacePin Assignment and Wire Colors MD-CS10x-000 CordsetMD-CS20x-000 Cordset MD-CS201-000Interfacing the Internal Differential Optical Encoder Pin ConfigurationFactory Mounted Encoder Encoder Signals Differential EncoderFeatures Linear Slide OptionMDrive34Plus Linear Slide Speed-Force Limitations†Specifications Mechanical SpecificationsWarranty Excellence in Motion