Intelligent Motion Systems MDriveAC manual Oz-in/810 N-cm

Page 56

Motor Specifications

Single Length

Holding Torque	1147 oz-in/810 N-cm
Detent Torque	35 oz-in/25 N-cm
Rotor Inertia	0.0917 oz-in-sec2/6.5 kg-cm2
Weight (Motor + Driver)	14.07 lb/6.38 kg

Double Length

Holding Torque	2294 oz-in/1620 N-cm
Detent Torque	84 oz-in/59 N-cm
Rotor Inertia	0.1833 oz-in-sec2/13 kg-cm2
Weight (Motor + Driver)	21.25 oz/9.64 kg

Appendices

A-5

Image 56

Contents 34 TM Low Voltage Installation Information UL Application Details and Conditions of AcceptanceTable Of Contents Appendices List Of Figures List of Tables Connecting AC Power Connect Opto Power and Logic InputsMDriveAC Plus Microstepping Before You BeginConnecting Parameter Setup Cable Install the IMS SPI Motor InterfacePart Hardware Specifications Intentionally Left Blank Introduction to the MDrive34AC Plus Microstepping ConfiguringFeatures and Benefits Page MDrive34AC Plus Microstepping Detailed Specifications General SpecificationsSetup Parameters Single LengthMechanical Specifications Dimensions in Inches mmP1 19-Pin M23 Connector I/O and SPI Communications Pin Assignment and DescriptionPin Assignment P1 I/O, SPI and Encoder Connections Pin Options and AccessoriesP3 Connector AC Power Introduction to the MDrive42AC Plus Microstepping Page MDrive42AC Plus Microstepping Detailed Specifications Setup Parameters 76.2 Pin Assignment and Description Pin Assignment P1 I/O, SPI and Encoder Connections Outside Pins 1 Options and Accessories Part Interfacing Configuring Intentionally Left Blank Optically Isolated Logic Inputs Isolated Logic Input Pins and ConnectionsLogic Interface and Connection Step Clock DirectionQuadrature Up/DownDirection StepChannel a Channel BOptocoupler Reference Optocoupler ReferenceInput Connection Examples Open Collector Interface ExampleSwitch Fault Temperature Warning OutputSwitch Interface Example 7 Fault Output interfaced to an LED Minimum Required ConnectionsConnecting SPI Communications SPI Clock SPI Pins and ConnectionsSPI Master with Multiple MDriveAC Plus Microstepping Color Coded Parameter Values Using the IMS SPI Motor Interface InstallationConfiguration Parameters and Ranges Motion Settings Screen Read-Only Part Serial Number Screen IMS SPI Motor Interface Menu OptionsFile ViewHelp UpgradeRecall Screen 1 The Motion Settings Configuration Screen Msel Microstep Resolution SelectionConnected/Disconnected Indicator FactorySet ExitScreen 2 I/O Settings Configuration Screen Enable Active High/LowInput Clock Type Input Clock FilterIMS IMS Serial Number Fault IndicationIMS Part Number/Serial Number Screen Upgrading the Firmware in the MDriveAC Plus Microstepping IMS SPI Upgrader ScreenUpgrade Instructions Initialization Screen Port MenuCheck Sum Calculation for SPI Using User-Defined SPISPI Timing Notes SPI Commands and Parameters MSBWrite SPI Communications SequenceIntentionally Left Blank Appendices MDriveAC Plus Microstepping Hardware Revision R121707 MDriveAC Plus Microstepping Motor Performance MDrive34AC 120VACMDrive34AC 240VAC Single LengthDouble Length Triple LengthMDrive42AC Plus Microstepping MDrive42AC 120VACOz-in/810 N-cm MDrive with Planetary Gearbox Section OverviewProduct Overview Selecting a Planetary GearboxReduction Ratio Calculating the Shock Load Output Torque TABFactors Nominal Output Torque Speed in Full Steps per SecondShock Load Output Torque =1.6 =1.7 =1.9Lead Screw System InertiaType of System Conveyor Belt Rack and PinionRotary Table Belt DriveChain Drive Figure B.6 Chain Drive System Inertia ConsiderationsPM81 Gearbox Ratios and Part Numbers Planetary Gearbox for MDrive34AC Plus2MDrive34AC Plus2 Planetary Gearbox Parameters PM105 Gearbox Ratios and Part Numbers Planetary Gearbox for MDrive42AC Plus2MDrive42AC Plus2 Planetary Gearbox Parameters PM105 MDrive42AC Plus2 Planetary Gearbox Parameters PM120 PM120 Gearbox Ratios and Part NumbersMD-CC300-000 USB to SPI Parameter Setup Cable Installation Procedure for the MX-CC300-000Installing the Cable/VCP Drivers Optional Cables and CordsetsFigure C.4 Hardware Update Wizard Screen Figure C.7 Hardware Update Wizard Finish Installation Determining the Virtual COM Port VCPAdapter To Controller InterfacePin Assignment and Wire Colors MD-CS10x-000 CordsetMD-CS20x-000 Cordset MD-CS201-000Factory Mounted Encoder Pin ConfigurationInterfacing the Internal Differential Optical Encoder Encoder Signals Differential EncoderFeatures Linear Slide OptionMDrive34Plus Linear Slide Speed-Force Limitations†Specifications Mechanical SpecificationsWarranty Excellence in Motion