Intelligent Motion Systems MDriveAC manual MDrive42AC Plus Microstepping Detailed Specifications

Page 21

SECTION 1.4

MDrive42AC Plus Microstepping Detailed Specifications

Electrical Specifications

Input Voltage (+VAC) Range (120 VAC MDrive)

95 to 132 VAC @ 50/60 Hz

Input Current (120 VAC MDrive)

5.6 A Maximum

Input Voltage (+VAC) Range (240 VAC MDrive)

95 to 264 VAC @ 50/60 Hz

Input Current (240 VAC MDrive)

2.8 A Maximum

Thermal Specifications

Heat Sink Temperature (non-condensing humidity)

-40°C to +75°C

Motor Temperature (non-condensing humidity)

-40°C to +90°C

I/O Specifications

Isolated Inputs — Step Clock, Direction and Enable

Resolution

10 Bit

Voltage Range (Sourcing or Sinking)

+5 to +24 VDC

Current (+5 VDC Max)

8.7 mA

Current (+24 VDC Max)

14.6 mA

Communications Specifications

Protocol

SPI

Motion Specifications

Microstep Resolution

Number of Resolutions

20

Available Microsteps Per Revolution

200

400

800

1000

1600

2000

3200

5000

6400

10000

12800

20000

25000

25600

40000

50000

51200

360001

216002

254003

1 = 0 . 0 1 d e g / µ s t e p

2 = 1 a r c m i n u t e / µ s t e p

3 = 0 . 0 0 1 m m / µ s t e p

Digital Filter Range

50 nS to 12.9 µS

(10 MHz to 38.8kHz)

Step/Direction,

Clock Types

Quadrature, Clock

Up/Clock Down

Step Frequency (Max)

5.0 MHz

Step Frequency Minimum Pulse Width

100 nS

WARNING!

Because the MDrive consists of two core

components, a drive and a motor, close attention must be paid to the thermal environment where the device is used. See Thermal Specifications.

Motor Specifications

Single Length

Holding Torque

Detent Torque

Rotor Inertia

Weight (Motor + Driver)

Double Length

Holding Torque

Detent Torque

Rotor Inertia

Weight (Motor + Driver)

1147 oz-in/810 N-cm

35 oz-in/25 N-cm

0.0917 oz-in-sec2/6.5 kg-cm2

14.07 lb/6.38 kg

2294 oz-in/1620 N-cm

84 oz-in/59 N-cm

0.1833 oz-in-sec2/13 kg-cm2

21.25 lb/9.64 kg

Part 1: Hardware Specifications

1-15

Image 21

Contents 34 TM UL Application Details and Conditions of Acceptance Low Voltage Installation InformationTable Of Contents Appendices List Of Figures List of Tables Connect Opto Power and Logic Inputs Connecting AC PowerMDriveAC Plus Microstepping Before You BeginInstall the IMS SPI Motor Interface Connecting Parameter Setup CablePart Hardware Specifications Intentionally Left Blank Configuring Features and BenefitsIntroduction to the MDrive34AC Plus Microstepping Page General Specifications MDrive34AC Plus Microstepping Detailed SpecificationsSingle Length Setup ParametersDimensions in Inches mm Mechanical SpecificationsPin Assignment and Description P1 19-Pin M23 Connector I/O and SPI CommunicationsPin Assignment P1 I/O, SPI and Encoder Connections Options and Accessories P3 Connector AC PowerPin Introduction to the MDrive42AC Plus Microstepping Page MDrive42AC Plus Microstepping Detailed Specifications Setup Parameters 76.2 Pin Assignment and Description Pin Assignment P1 I/O, SPI and Encoder Connections Outside Pins 1 Options and Accessories Part Interfacing Configuring Intentionally Left Blank Isolated Logic Input Pins and Connections Logic Interface and ConnectionOptically Isolated Logic Inputs Direction Step ClockQuadrature Up/DownStep DirectionChannel a Channel BOptocoupler Reference Optocoupler ReferenceOpen Collector Interface Example Input Connection ExamplesFault Temperature Warning Output Switch Interface ExampleSwitch Minimum Required Connections 7 Fault Output interfaced to an LEDConnecting SPI Communications SPI Pins and Connections SPI Master with Multiple MDriveAC Plus MicrosteppingSPI Clock Using the IMS SPI Motor Interface Installation Configuration Parameters and RangesColor Coded Parameter Values IMS SPI Motor Interface Menu Options Motion Settings Screen Read-Only Part Serial Number ScreenFile ViewUpgrade RecallHelp Msel Microstep Resolution Selection Screen 1 The Motion Settings Configuration ScreenFactory Connected/Disconnected IndicatorSet ExitEnable Active High/Low Screen 2 I/O Settings Configuration ScreenInput Clock Type Input Clock FilterFault Indication IMS Part Number/Serial Number ScreenIMS IMS Serial Number IMS SPI Upgrader Screen Upgrade InstructionsUpgrading the Firmware in the MDriveAC Plus Microstepping Port Menu Initialization ScreenUsing User-Defined SPI SPI Timing NotesCheck Sum Calculation for SPI MSB SPI Commands and ParametersSPI Communications Sequence WriteIntentionally Left Blank Appendices MDriveAC Plus Microstepping Hardware Revision R121707 MDrive34AC 120VAC MDriveAC Plus Microstepping Motor PerformanceMDrive34AC 240VAC Single LengthTriple Length Double LengthMDrive42AC Plus Microstepping MDrive42AC 120VACOz-in/810 N-cm Section Overview MDrive with Planetary GearboxProduct Overview Selecting a Planetary GearboxCalculating the Shock Load Output Torque TAB FactorsReduction Ratio Speed in Full Steps per Second Nominal Output Torque=1.6 =1.7 =1.9 Shock Load Output TorqueSystem Inertia Type of SystemLead Screw Rack and Pinion Conveyor BeltBelt Drive Rotary TableFigure B.6 Chain Drive System Inertia Considerations Chain DrivePlanetary Gearbox for MDrive34AC Plus2 MDrive34AC Plus2 Planetary Gearbox ParametersPM81 Gearbox Ratios and Part Numbers Planetary Gearbox for MDrive42AC Plus2 MDrive42AC Plus2 Planetary Gearbox Parameters PM105PM105 Gearbox Ratios and Part Numbers PM120 Gearbox Ratios and Part Numbers MDrive42AC Plus2 Planetary Gearbox Parameters PM120Installation Procedure for the MX-CC300-000 MD-CC300-000 USB to SPI Parameter Setup CableInstalling the Cable/VCP Drivers Optional Cables and CordsetsFigure C.4 Hardware Update Wizard Screen Determining the Virtual COM Port VCP Figure C.7 Hardware Update Wizard Finish InstallationTo Controller Interface AdapterMD-CS10x-000 Cordset Pin Assignment and Wire ColorsMD-CS201-000 MD-CS20x-000 CordsetPin Configuration Interfacing the Internal Differential Optical EncoderFactory Mounted Encoder Differential Encoder Encoder SignalsLinear Slide Option FeaturesMDrive34Plus Linear Slide Speed-Force Limitations†Mechanical Specifications SpecificationsWarranty Excellence in Motion