GE LP11U user manual LP 5/6/8/10-11U 208-240V input

Page 47

g

Digital EnergyLP Series

LP 5/6/8/10-11U 208-240V input

h

w

LEVELLER

POSITION A: FIX UPS TO THE FLOOR

POSITION B: LIFT UPS CASTORS FROM THE FLOOR

d

MANUAL BYPASS SWITCH

NORMAL: POSITION 1 (LOAD ON UPS)

SERVICE: POSITION 2 (LOAD ON BYPASS)

INPUT/OUTPUT TERMINALS

OUTPUT INPUT

EARTH

CONNECTION

IS ESSENTIAL

CASTORS

CONDUIT BOX

CABLE ENTRY

SUB-D PINNING

5 - COMMON

9 - GENERAL ALARM

4 - NOT USED

8 - MAINS FAILURE

3 - SERIAL DATA IN / UPS SHUTDOWN

7 - PLUG&PLAY / RTS

2 - SERIAL DATA OUT

6 - BYPASS ACTIVE

1 - BATTERY LOW

BATTERY FUSES

CONTROLS / CIRCUIT BREAKERS

UPS UTILITY BYPASS

ON

OFF

BATTERY PACK CONNECTOR

OPTION SLOTS

RS232 / CONTACT, SEE BELOW

SNMP CARD OR RELAY CARD

RPA CARD

PARALLEL OPERATION

RS232 / CONTACT INTERFACE

BATTERY

DISCONNECTED

EMERGENCY

SHUTDOWN

Image 47
Contents Digital Energy LP 11U Page Digital Energy LP Series Important Safety Instructions Interfacing Features General Important Safety InstructionsInstallation Batteries StorageDescription WarrantyIntroduction Principles of Operation Functional ExplanationAutomatic Bypass Switch Location InstallationPackage Contents Transport UnpackingUPS model Tightening torque force Utility voltage UPS model 120V 208V 240VOutput voltage UPS model 120V 208V 240V LP 5/68/10-11U Standard installation procedure LP 5/6-11U Installation procedure 120V input Bypass tap changed to 240 Volt Bypass tap factory setting 208 VoltAvailable input voltages hardware modifications Input voltage 208 or 240VacOutput voltage 208Vac Input voltage 120Vac optional, 5/6kVA onlyAvailable output voltages hardware modifications LP 5/6/8/10-11U Output tap change Output voltage 120Vac split-phaseOutput voltage 220/230/240Vac Output voltage 120Vac single phaseOutput Voltage Setup ScreensInput Voltage Input Voltage Change toLP 5/6/8/10-11U Installation of battery pack Installation of parallel operating LP-U UPSs Autorestart OFF Press Enter Autorestart OFF Setting MismatchManual bypass MaintenanceECO-mode No-load shutdownDescription of Front and Rear Panel OperationRear panel Step-up transformer Rear panel of the step-up transformerSelftest Progress Start-upAutonomy Time Left Operating Time 0YEAR 29DAYS Battery 23CUse Input LineTemp TOO High On Line Alarm Press UPStatus and Alarm Menu Inverter OFF Battery Charger no Float Capacitor C1 Capacity LOWBattery Depleted Software Version R2.9 FAN Speed INV.DC + Service ScreensService Menu Input and Output not SynchronizedTstamp Q4 Automatic Bypass EnabledFAN Curve Language English Input Voltage Output VoltageOutput Frequency Frequency Range 2% PLL Lock Speed NormalTest Screens Automatic Bypass Enabled Service Warning DisabledQuick Battery Test Start Calibrate BAT Test Activated Deep Battery TestProcedure Utility start Other FeaturesOverload protection in bypass mode ShutdownAuto restart Superior Battery ManagementECO Auto Restart OFF Press EnterRelay Card optional Snmp Interface optional Interfacing FeaturesRS232 / contact interface Emergency shutdownRPA-Facility Redundant Parallel Architecture Optional FeaturesExtended Runtime Plug-in CardsSeismic anchors PDM Power Distribution ModuleCooling fan MaintenanceSafety Recycling the UPS at the end of service lifeSelftest Failure Q4 not OK TroubleshootingSelftest Failure Temp TOO High UPS Type 11U 10-11U SpecificationsAutomatic Bypass Switch Enclosure Center of Gravity Dimensions Conduit BoxLP 5/6/8/10-11U installation drawings LP 5/6/8/10-11U 208-240V input LP 5/6-11U 120V input