GE LP11U user manual LP 5/6-11U 120V input

Page 48

g

LP 5/6-11U 120V input

d

Digital Energy™ LP Series

MANUAL BYPASS SWITCH

NORMAL: POSITION 1 (LOAD ON UPS)

SERVICE: POSITION 2 (LOAD ON BYPASS)

INPUT/OUTPUT

OUTPUT INPUT

EARTH

CONNECTION

IS ESSENTIAL

h

CASTORS

w

LEVELLER

CONDUIT BOX

CABLE ENTRY

INPUT TERMINALS

EARTH

CONNECTION

IS ESSENTIAL

BATTERY FUSES

CONTROLS / CIRCUIT BREAKERS

UPS UTILITY BYPASS

ON

OFF

BATTERY PACK CONNECTOR

OPTION SLOTS

RS232 / CONTACT, SEE BELOW

SNMP CARD OR RELAY CARD

RPA CARD

PARALLEL OPERATION

RS232 / CONTACT INTERFACE

BATTERY

DISCONNECTED

EMERGENCY

SHUTDOWN

SUB-D PINNING

5 - COMMON

9 - GENERAL ALARM

4 - NOT USED

8 - MAINS FAILURE

3 - SERIAL DATA IN /

UPS SHUTDOWN 7 - PLUG&PLAY / RTS 2 - SERIAL DATA OUT 6 - BYPASS ACTIVE 1 - BATTERY LOW

POSITION A: FIX UPS TO THE FLOOR

POSITION B: LIFT UPS CASTORS FROM THE FLOOR

Image 48

Contents Digital Energy LP 11U Page Digital Energy LP Series Important Safety Instructions Interfacing Features Important Safety Instructions InstallationGeneral Storage BatteriesWarranty IntroductionDescription Functional Explanation Principles of OperationAutomatic Bypass Switch Installation Package ContentsTransport Unpacking LocationUtility voltage UPS model 120V 208V 240V Output voltage UPS model 120V 208V 240VUPS model Tightening torque force LP 5/68/10-11U Standard installation procedure LP 5/6-11U Installation procedure 120V input Bypass tap factory setting 208 Volt Available input voltages hardware modificationsInput voltage 208 or 240Vac Bypass tap changed to 240 VoltInput voltage 120Vac optional, 5/6kVA only Available output voltages hardware modificationsOutput voltage 208Vac Output voltage 120Vac split-phase LP 5/6/8/10-11U Output tap changeOutput voltage 120Vac single phase Output voltage 220/230/240VacSetup Screens Input VoltageInput Voltage Change to Output VoltageLP 5/6/8/10-11U Installation of battery pack Installation of parallel operating LP-U UPSs Autorestart OFF Setting Mismatch Autorestart OFF Press EnterMaintenance ECO-modeNo-load shutdown Manual bypassOperation Description of Front and Rear PanelRear panel of the step-up transformer Rear panel Step-up transformerStart-up Selftest ProgressBattery 23C UseInput Line Autonomy Time Left Operating Time 0YEAR 29DAYSOn Line Alarm Press UP Status and Alarm MenuTemp TOO High Battery Charger no Float Capacitor C1 Capacity LOW Battery DepletedInverter OFF Service Screens Service MenuInput and Output not Synchronized Software Version R2.9 FAN Speed INV.DC +Automatic Bypass Enabled Tstamp Q4Language English Input Voltage Output Voltage Output FrequencyFrequency Range 2% PLL Lock Speed Normal FAN CurveAutomatic Bypass Enabled Service Warning Disabled Quick Battery Test StartTest Screens Deep Battery Test ProcedureCalibrate BAT Test Activated Other Features Overload protection in bypass modeShutdown Utility startSuperior Battery Management ECOAuto Restart OFF Press Enter Auto restartInterfacing Features RS232 / contact interfaceEmergency shutdown Relay Card optional Snmp Interface optionalOptional Features Extended RuntimePlug-in Cards RPA-Facility Redundant Parallel ArchitecturePDM Power Distribution Module Seismic anchorsMaintenance SafetyRecycling the UPS at the end of service life Cooling fanTroubleshooting Selftest Failure Temp TOO HighSelftest Failure Q4 not OK Specifications UPS Type 11U 10-11UAutomatic Bypass Switch Enclosure Dimensions Conduit Box Center of GravityLP 5/6/8/10-11U installation drawings LP 5/6/8/10-11U 208-240V input LP 5/6-11U 120V input