GE LP11U user manual Automatic Bypass Switch

Page 43

g

Digital EnergyLP Series

UPS Type

: 5-11U

6-11U

8-11U

10-11U

AUTOMATIC BYPASS SWITCH

The automatic switch provides transfer of the load to the utility voltage without any interruption of the supply. The transfer is initiated by a signal from the output converter protection circuit in case of an overload or high temperature.

When the conditions return to normal the load is automatically transferred back to the output converter. The automatic bypass switch can be disabled by the end-user.

Bypass voltage limits

Transfer transients

Frequency tracking range

Slew rate

BATTERY

Battery type

Nominal voltage (V) / capacity (Ah) Number of batteries

Capacity of standard battery set Battery recharge time Battery service life

Battery discharging

Runtime in minutes VA / Watts

1000 / 800

2000 / 1600

3000 / 2400

5000 / 4000

6000 / 4800

8000 / 6400

10000 / 8000

BATTERY EXTENSION PACKS

Sheet steel cubicle

Dimensions (hxwxd, mm)

Dimensions (hxwxd, inch)

Battery

Weight with battery (Kg)

Weight with battery (Lbs)

Battery pack A (voltage V / capacity Ah) Total capacity (Ah)

Typical runtime, 100% / 50% load, min. Number of packs required

Battery pack B (voltage V / capacity Ah) Total capacity (Ah)

Typical runtime, 100% / 50% load, min. Number of packs required

For more info see section 7.1

:-15%, +10% of nominal

:typically 2% mean deviation over one half cycle.

:± 2/4/6% of nominal (user selectable)

:max. 1Hz/sec or 5Hz/sec (user selectable)

:Sealed and maintenance free

:

12/7

12/7

12/12

12/12

:

20

20

20

20

:

7Ah

7Ah

12Ah

12Ah

:1.5 - 3 hours for 80% capacity

:up to 6 years (depending on operating conditions)

:self discharge current 0.35 mA

discharge end voltage of the battery depending on the actual load 10.5Vdc < 0.2 CA till 9.0 Vdc > 2 CA

When the UPS is in sleeping mode the inverter will be switched off, battery charger and rectifier are in operation

:

6060

120

120

:

4040

60

60

:

1818

40

40

:

1010

22

22

:

-

8

17

17

:

-

-

11

11

:

-

-

-

8

:VSDA1

:537x313x590

:21.1x12.3x23.2

:240Vdc/7Ah or 240Vdc/14Ah

:73 or 123

:161 or 271

:

240/7

240/7

240/7

240/7

:

14

14

19

19

:

25/60

21/50

22/50

16/39

:

1

1

1

1

:

240/14

240/14

240/14

240/14

:

21

21

26

26

:

45/90

35/75

33/70

25/57

:

1

1

1

1

STEP-UP TRANSFORMER CABINET MOUNTED UNDERNEATH VSD2 (FOR LP 5/6-11U ONLY)

Sheet steel cubicle

:

VSDT2 + VSD2

Dimensions (hxwxd, mm)

:

995x313x730

Dimensions (hxwxd, inch)

:

39.2x12.3x28.7

Weight (Kg)

:

175

Kg

Weight (Lbs)

:

386

Lbs

LX: OPM_LPU_11U_5K0_10K_1US_V030

41

GE DE LP 11U UPS: Installation / User Manual 3.0 (US)

Image 43
Contents Digital Energy LP 11U Page Digital Energy LP Series Important Safety Instructions Interfacing Features Installation Important Safety InstructionsGeneral Batteries StorageIntroduction WarrantyDescription Principles of Operation Functional ExplanationAutomatic Bypass Switch Location InstallationPackage Contents Transport UnpackingOutput voltage UPS model 120V 208V 240V Utility voltage UPS model 120V 208V 240VUPS model Tightening torque force LP 5/68/10-11U Standard installation procedure LP 5/6-11U Installation procedure 120V input Bypass tap changed to 240 Volt Bypass tap factory setting 208 VoltAvailable input voltages hardware modifications Input voltage 208 or 240VacAvailable output voltages hardware modifications Input voltage 120Vac optional, 5/6kVA onlyOutput voltage 208Vac LP 5/6/8/10-11U Output tap change Output voltage 120Vac split-phaseOutput voltage 220/230/240Vac Output voltage 120Vac single phaseOutput Voltage Setup ScreensInput Voltage Input Voltage Change toLP 5/6/8/10-11U Installation of battery pack Installation of parallel operating LP-U UPSs Autorestart OFF Press Enter Autorestart OFF Setting MismatchManual bypass MaintenanceECO-mode No-load shutdownDescription of Front and Rear Panel OperationRear panel Step-up transformer Rear panel of the step-up transformerSelftest Progress Start-upAutonomy Time Left Operating Time 0YEAR 29DAYS Battery 23CUse Input LineStatus and Alarm Menu On Line Alarm Press UPTemp TOO High Battery Depleted Battery Charger no Float Capacitor C1 Capacity LOWInverter OFF Software Version R2.9 FAN Speed INV.DC + Service ScreensService Menu Input and Output not SynchronizedTstamp Q4 Automatic Bypass EnabledFAN Curve Language English Input Voltage Output VoltageOutput Frequency Frequency Range 2% PLL Lock Speed NormalQuick Battery Test Start Automatic Bypass Enabled Service Warning DisabledTest Screens Procedure Deep Battery TestCalibrate BAT Test Activated Utility start Other FeaturesOverload protection in bypass mode ShutdownAuto restart Superior Battery ManagementECO Auto Restart OFF Press EnterRelay Card optional Snmp Interface optional Interfacing FeaturesRS232 / contact interface Emergency shutdownRPA-Facility Redundant Parallel Architecture Optional FeaturesExtended Runtime Plug-in CardsSeismic anchors PDM Power Distribution ModuleCooling fan MaintenanceSafety Recycling the UPS at the end of service lifeSelftest Failure Temp TOO High TroubleshootingSelftest Failure Q4 not OK UPS Type 11U 10-11U SpecificationsAutomatic Bypass Switch Enclosure Center of Gravity Dimensions Conduit BoxLP 5/6/8/10-11U installation drawings LP 5/6/8/10-11U 208-240V input LP 5/6-11U 120V input