Bay Technical Associates DS73, DS2-RPC, DS4-RPC, DS2-RPC DS4-RPC owner manual Ppp Dial-Up, Menu

Page 33

DS-RPC OWNER’S MANUAL

DETAILED OPERATION AND CONFIGURATION

__________________________________________________________________________________________

PPP DIAL-UP	Using Windows 95 Dial-Up Networking
CONNECTION	or another dial-up networking program with
	PPP, dial the modem connected to the host
	module. The Host Module sends the main
	menu:

Data Switch Series - F.0.10

Bay Technical Associates

Unit ID: DS71-MD2

Port Select Code: $BT

Attention Character: ;

Device A	(2,1)	1
Device B	(2,2)	2
Device C	(2,3)	3
Device D	(2,4)	4
DS73	(3,1)	5
Configure		C
I/O Modules Reset		RM
Unit Reset		RU
Exit		X
Logout		T
Enter Request:

From the host module main menu, select the DS73TP module connected to the network or exit from the main menu and send the ASCII character string to select the DS73TP module. The DS73TP sends the following header and prompts for user name.

DS73TP Ethernet Module

F.0.01 Copyright (c) 1997

Bay Technical Associates

Enter User Name:

Use the F7 key as described in Appendix C.

Once login is successful and a network connection has been established, Telnet (using the IP Address) to any device on the network.

25

Image 33

Contents BayTech Manual Publication #U140A124-01 August DS-RPC Data SWITCH/POWER ControlPage Iii Page Introduction to the DS-RPC DS71-MD2 Technical Support Page Introduction to the DS-RPC Page Programmable Features of the DS Modules Feature Description ActionDS71 or DS71-MD2 Host Module Feature Description Action DS71-MD2 Host Module Programmable Features of the DS Modules con’tModule Feature Description Action DS73TP N EtworkDS-RPC Quick Start EIA-232 Serial ConnectionOperation Selecting a Device DS-RPC Module Configuration RPC Unpacking InstallationPower Preparing the Installation SitePower ON/OFF State Power UP SequenceCircuit Breaker Cabling RJ-45 Cables and AdaptersDS73TP Connection DS71 EIA-232 RJ-45 Pin/Signal Definition DS74 EIA-232 RJ-45 Pin/Signal Definition Modem Connections PIN Connecting to the DS-RPC Detailed Operation ConfigurationEIA-232 Serial ConnectionDS71-MD2 only Detailed Operation and Configuration Operation Device a Device B Device C Device D Selection Menu DrivenAscii Character String$BT2,1cr$BTBcr Binary ModeTerminate Binary ModeMenu PPP DIAL-UPConfiguration Status Or this for the DS71-MD2Serial Port ConfigurationDTR RTS 115.2K None Off High Exit/Save..….......1 If you have made necessary changes to Cr. New configuration changes are storedHost device, type Y for yes, followed by Selecting #1 will give the same results asFor For 57.6K a for 76.8K B for 115.2K Enter Request For DTR RTS Host Port Select User programmable. Default Port SelectCode Code is $BTCharacter Guard is disabled Default Connect Port ID Echo is disabled Connect PortID Echo Login Setup Header is enabledHeader Default Password is BTA, disabled. PasswordMenu Auto Connect Port If enabled, the following header and menu appearsSerial connection Port is disabled Escape Character ........… Rings to DisabledAnswer Rings to Answer isDefault Connectivity Timeout is TimeoutConnectivity MinutesEscape Default Escape Character is 43, which isCharacter 2B Hex or a plus sign +Unit Reset Identifies the unit. Default Unit ID is DS71Unit ID Or DS71-MD2Ascii DrivenPort Device Name …..............................3 Selections 1-8 are fully programmable DS73TP Enter password Dial-UP Default Dial-Up IP Address is Default Subnet Mask isSubnet Mask Gateway Default Gateway address isPrimary DNSMenu. Default Secondary DNS address is Default Primary DNS address isSecondary 0.0Default Primary Nbns address is Default Secondary Nbns address isNbns Default User Name is user1 Default Password is BTAUser Name Default Module Name is DS73TP ModuleName RPC Operation Accessing Main MenuControlling Receptacles Outlet 1, Outlet 2, Outlet 3, Outlet DS-RPC Config Change PasswordOutlet Outlet 4 Enter Request Enable/Disable Is EnabledConfirmation RPC Technical Support Module DS-RPC Model DS-RPC Serial NumberOutlet OUTLET3 OutletREPACKAGING, Shipping and Returning to the Factory Call BayTech to get a Return Authorization NumberFCC Requirements for the DS71-MD2 FCC Radio Frequency Interface StatementFCC Radio Frequency Interface Statement Specifications Appendix aTable A.1 Base DS71 Host DS71-MD2 DS74 Appendix B Save modem’s configuration in non-volatile memory Rockwell Chip SET Modems Command InterpretationAppendix C MY ComputerMake NEW Connection DIAL-UP Networking PropertiesPost Dial Terminal Screen DS71 Mechanical Layout Appendix D DrawingsDS71-MD2 Mechanical Layout DS74 Mechanical Layout DS73 Mechanical Layout Ascii Character Definition Appendix EBreak condition · Rings to Answer · 45, 46 RTS/DTR Line Driver · 29, 31 XON/XOFF ·