Bay Technical Associates DS73, DS2-RPC, DS4-RPC, DS2-RPC DS4-RPC Properties, DIAL-UP Networking

Page 87

DS-RPC OWNER’S MANUAL APPENDIX C

__________________________________________________________________________________________

APPENDIX C

PROPERTIES

ØHighlight the device you have just created.

ØSelect “File” from the Windows task bar.

ØSelect “Properties.”

ØSelect “General.”

ØSelect “Configure.” Ensure the information is correct.

ØSelect “Options.” Enable “Bring up Terminal Window after Dialing.”

ØClick “OK.”

ØSelect “Server Type”.

ØIn the “Server Type” Menu, select “PPP: Windows 95, Windows NT, 3.5, Internet.”

ØIn the “Advanced Options;” Enable software compression.

ØIn the “Allowed Network Protocols;” Enable TCP/IP.

ØClick “TCP/IP Settings.” Enable the following settings. You must enable Header Compression.

∙Server Assigned IP Address

∙Server Assigned Name Server Address

∙Use IP Header Compression

∙User default gateway on remote network

ØClick “OK” three times.

ØYou should be in the Dial-Up Networking screen.

ØSelect the device you are adding. The icon for the device you are dialing appears on the Dial-Up Networking screen.

DIAL-UP NETWORKING

ØIn the Dial-Up Networking Window, double click the device you are dialing.

ØClick “Connect To.”

ØUser Name. Enter the user name programmed in the DS73TP.

Default User Name is user1.

ØEnter the password programmed in the DS73TP.

ØDefault password is BTA.

79

Image 87

Contents BayTech Manual Publication #U140A124-01 August DS-RPC Data SWITCH/POWER ControlPage Iii Page Introduction to the DS-RPC DS71-MD2 Technical Support Page Introduction to the DS-RPC Page Programmable Features of the DS Modules Feature Description ActionDS71 or DS71-MD2 Host Module Feature Description Action DS71-MD2 Host Module Programmable Features of the DS Modules con’tModule Feature Description Action DS73TP N EtworkDS-RPC Quick Start EIA-232 Serial ConnectionOperation Selecting a Device DS-RPC Module Configuration RPC Unpacking InstallationPower Preparing the Installation SitePower ON/OFF State Power UP SequenceCircuit Breaker Cabling RJ-45 Cables and AdaptersDS73TP Connection DS71 EIA-232 RJ-45 Pin/Signal Definition DS74 EIA-232 RJ-45 Pin/Signal Definition Modem Connections PIN Connection Detailed Operation ConfigurationConnecting to the DS-RPC EIA-232 SerialDS71-MD2 only Detailed Operation and Configuration Operation Device a Device B Device C Device D String Menu DrivenSelection Ascii CharacterMode Binary Mode$BT2,1cr$BTBcr Terminate BinaryMenu PPP DIAL-UPConfiguration Status Or this for the DS71-MD2Serial Port ConfigurationDTR RTS 115.2K None Off High Exit/Save..….......1 Selecting #1 will give the same results as Cr. New configuration changes are storedIf you have made necessary changes to Host device, type Y for yes, followed byFor For 57.6K a for 76.8K B for 115.2K Enter Request For DTR RTS Host Code is $BT User programmable. Default Port SelectPort Select CodeCharacter Guard is disabled Default Connect Port ID Echo is disabled Connect PortID Echo Login Setup Header is enabledHeader Default Password is BTA, disabled. PasswordMenu Auto Connect Port If enabled, the following header and menu appearsSerial connection Port is disabled Escape Character ........… Rings to Answer is DisabledRings to AnswerMinutes TimeoutDefault Connectivity Timeout is Connectivity2B Hex or a plus sign + Default Escape Character is 43, which isEscape CharacterOr DS71-MD2 Identifies the unit. Default Unit ID is DS71Unit Reset Unit IDAscii DrivenPort Device Name …..............................3 Selections 1-8 are fully programmable DS73TP Enter password Dial-UP Default Dial-Up IP Address is Default Subnet Mask isSubnet Mask DNS Default Gateway address isGateway Primary0.0 Default Primary DNS address isMenu. Default Secondary DNS address is SecondaryDefault Primary Nbns address is Default Secondary Nbns address isNbns Default User Name is user1 Default Password is BTAUser Name Default Module Name is DS73TP ModuleName RPC Operation Accessing Main MenuControlling Receptacles Outlet 1, Outlet 2, Outlet 3, Outlet DS-RPC Config Change PasswordOutlet Outlet 4 Enter Request Enable/Disable Is EnabledConfirmation RPC Technical Support OUTLET3 Outlet DS-RPC Model DS-RPC Serial NumberModule OutletREPACKAGING, Shipping and Returning to the Factory Call BayTech to get a Return Authorization NumberFCC Requirements for the DS71-MD2 FCC Radio Frequency Interface StatementFCC Radio Frequency Interface Statement Specifications Appendix aTable A.1 Base DS71 Host DS71-MD2 DS74 Appendix B Save modem’s configuration in non-volatile memory Rockwell Chip SET Modems Command InterpretationAppendix C MY ComputerMake NEW Connection DIAL-UP Networking PropertiesPost Dial Terminal Screen DS71 Mechanical Layout Appendix D DrawingsDS71-MD2 Mechanical Layout DS74 Mechanical Layout DS73 Mechanical Layout Ascii Character Definition Appendix EBreak condition · Rings to Answer · 45, 46 RTS/DTR Line Driver · 29, 31 XON/XOFF ·