Bay Technical Associates DS73, DS2-RPC, DS4-RPC, DS2-RPC DS4-RPC Serial Port, Configuration

Page 36

DS-RPC OWNER’S MANUAL

DETAILED OPERATION AND CONFIGURATION

__________________________________________________________________________________________

The status of the following features appears:

Installed Modules: 1, 2, 3, …(etc)

 

Port Select Code is

$BT

Attention Character is

;

Disconnect Time Guard is

Disabled

Port ID Echo is

Disabled

Unit ID is

DS71-MD2 (or DS71)

DCD Logon/Logoff is ……………..Disabled (DS71 only)

NOTE: The entries in parentheses are added to help clarify what you may see in the menu. These parentheses do not appear on your screen.

Local Modem Setup: (* DS71-MD2 only)

Rings to Auto-Answer

2 (*)

Modem to Modem Xon/Xoff FlowControl..Disabled (*)

Modem Connectivity is .........…. 60 minutes (*)

Escape Character is ..............…. 43 + (*)

Login Setup:

 

Header is

Enabled

Password is

Disabled

Menu is

Enabled

Auto Connect Port is

Module 2, Port 1

Auto Connect is

Disabled

Strike Any Key to Continue

Port

Device

Baud

Word

Stop

Parity

Xon/

Xoff/

Line

Drive

 

Name

Rate

Size

Bits

 

Xmit

Recv

DTR

RTS

1

Host EIA-232

9600

8

1

None

Off

Off

High

High

2

Host Modem

57.6k

8

1

None

Off

Off

High

High

Strike any Key to Continue

Note: On the DS71 module only Port 1 will be displayed since there is no Host Modem installed.

SERIAL PORT

DS-RPC host modules translate data

CONFIGURATION

for devices using different serial

 

configurations. See Appendix A,

 

“SPECIFICATIONS” for available serial

 

parameters. Default Serial Port

 

Configurations are 9600 bps, 8 data bits,

 

1 stop bit, no parity, Xon/Xoff disabled,

 

RTS high, and DTR low.

28

Page 35 Page 37
Image 36
Page 35 Page 37
Contents DS-RPC Data SWITCH/POWER Control BayTech Manual Publication #U140A124-01 AugustPage Iii Page Introduction to the DS-RPC DS71-MD2 Technical Support Page Introduction to the DS-RPC Page Programmable Features of the DS Modules Feature Description ActionDS71 or DS71-MD2 Host Module Programmable Features of the DS Modules con’t Feature Description Action DS71-MD2 Host ModuleFeature Description Action DS73TP N Etwork ModuleDS-RPC Quick Start EIA-232 Serial ConnectionOperation Selecting a Device DS-RPC Module Configuration RPC Installation UnpackingPreparing the Installation Site PowerPower ON/OFF State Power UP SequenceCircuit Breaker Cabling RJ-45 Cables and AdaptersDS73TP Connection DS71 EIA-232 RJ-45 Pin/Signal Definition DS74 EIA-232 RJ-45 Pin/Signal Definition Modem Connections PIN Detailed Operation Configuration Connecting to the DS-RPCEIA-232 Serial ConnectionDS71-MD2 only Detailed Operation and Configuration Operation Device a Device B Device C Device D Menu Driven SelectionAscii Character StringBinary Mode $BT2,1cr$BTBcrTerminate Binary ModePPP DIAL-UP MenuConfiguration Or this for the DS71-MD2 StatusConfiguration Serial PortDTR RTS 115.2K None Off High Exit/Save..….......1 Cr. New configuration changes are stored If you have made necessary changes toHost device, type Y for yes, followed by Selecting #1 will give the same results asFor For 57.6K a for 76.8K B for 115.2K Enter Request For DTR RTS Host User programmable. Default Port Select Port SelectCode Code is $BTCharacter Guard is disabled Default Connect Port ID Echo is disabled Connect PortID Echo Login Setup Header is enabledHeader Password Default Password is BTA, disabled.Menu If enabled, the following header and menu appears Auto Connect PortSerial connection Port is disabled Escape Character ........… Disabled Rings toAnswer Rings to Answer isTimeout Default Connectivity Timeout isConnectivity MinutesDefault Escape Character is 43, which is EscapeCharacter 2B Hex or a plus sign +Identifies the unit. Default Unit ID is DS71 Unit ResetUnit ID Or DS71-MD2Driven AsciiPort Device Name …..............................3 Selections 1-8 are fully programmable DS73TP Enter password Dial-UP Default Dial-Up IP Address is Default Subnet Mask isSubnet Mask Default Gateway address is GatewayPrimary DNSDefault Primary DNS address is Menu. Default Secondary DNS address isSecondary 0.0Default Primary Nbns address is Default Secondary Nbns address isNbns Default User Name is user1 Default Password is BTAUser Name Default Module Name is DS73TP ModuleName Accessing Main Menu RPC OperationControlling Receptacles Outlet 1, Outlet 2, Outlet 3, Outlet Change Password DS-RPC ConfigOutlet Outlet 4 Enter Request Enable/Disable Is EnabledConfirmation RPC Technical Support DS-RPC Model DS-RPC Serial Number ModuleOutlet OUTLET3 OutletCall BayTech to get a Return Authorization Number REPACKAGING, Shipping and Returning to the FactoryFCC Radio Frequency Interface Statement FCC Requirements for the DS71-MD2FCC Radio Frequency Interface Statement Specifications Appendix aTable A.1 Base DS71 Host DS71-MD2 DS74 Appendix B Rockwell Chip SET Modems Command Interpretation Save modem’s configuration in non-volatile memoryAppendix C MY ComputerMake NEW Connection Properties DIAL-UP NetworkingPost Dial Terminal Screen Appendix D Drawings DS71 Mechanical LayoutDS71-MD2 Mechanical Layout DS74 Mechanical Layout DS73 Mechanical Layout Appendix E Ascii Character DefinitionBreak condition · Rings to Answer · 45, 46 RTS/DTR Line Driver · 29, 31 XON/XOFF ·
Top Page Image Contents