Bay Technical Associates DS2-RPC DS4-RPC, DS73, DS2-RPC, DS4-RPC owner manual Enter password

Page 62

DS-RPC OWNER’S MANUAL

DETAILED OPERATION AND CONFIGURATION

__________________________________________________________________________________________

DS73TP Ethernet Module

F.0.02 Copyright (C) 1997

Bay Technical Associates

Enter user name :

Enter the current user name; default user name is user1. The module prompts for a password:

Enter password:

Enter the current password; Default Password is BTA. The following configuration menu appears:

NOTE: User name and password are case sensitive.

 

Module IP Address: 200.4.3.72

 

Dial-up IP Address

200.4.3.73

 

Subnet Mask:

255.255.255.0

 

Gateway Addr:

200.4.3.1

 

Primary DNS:

0.0.0.0

 

Secondary DNS:

0.0.0.0

 

Primary NBNS :

0.0.0.0

 

Secondary NBNS:

0.0.0.0

 

Ethernet Addr:

00.C0.48.1A.24.5D

 

Network Cable Connections: good

 

Module IP Address..............…..................................1

 

Dial-in IP Address..................…................................2

 

Subnet Mask..............................….............................3

 

Gateway........................................…..........................4

 

Primary DNS ...................................….......................5

 

Secondary DNS .…..............................…....................6

 

Primary NBNS .....................................…....…...........7

 

Secondary NBNS ...................................….................8

 

User Name................................................…...............9

 

Password.........................................................….......10

 

Module Name .....................................................…...11

 

Exit....................................................................….....X

Module

The IP address is the network address

IP Address

assigned by your network manager for your

 

network.The IP Address consist of four

 

bytes, each byte ranging from 0 to 255.

This parameter must be programmed before the DS73TP accesses the network.

54

Image 62
Contents DS-RPC Data SWITCH/POWER Control BayTech Manual Publication #U140A124-01 AugustPage Iii Page Introduction to the DS-RPC DS71-MD2 Technical Support Page Introduction to the DS-RPC Page DS71 or DS71-MD2 Host Module Programmable Features of the DS ModulesFeature Description Action Programmable Features of the DS Modules con’t Feature Description Action DS71-MD2 Host ModuleFeature Description Action DS73TP N Etwork ModuleOperation DS-RPC Quick StartEIA-232 Serial Connection Selecting a Device DS-RPC Module Configuration RPC Installation UnpackingPreparing the Installation Site PowerCircuit Breaker Power ON/OFF StatePower UP Sequence DS73TP Connection CablingRJ-45 Cables and Adapters DS71 EIA-232 RJ-45 Pin/Signal Definition DS74 EIA-232 RJ-45 Pin/Signal Definition Modem Connections PIN EIA-232 Serial Detailed Operation ConfigurationConnecting to the DS-RPC ConnectionDS71-MD2 only Detailed Operation and Configuration Operation Device a Device B Device C Device D Ascii Character Menu DrivenSelection StringTerminate Binary Binary Mode$BT2,1cr$BTBcr ModePPP DIAL-UP MenuConfiguration Or this for the DS71-MD2 StatusConfiguration Serial PortDTR RTS 115.2K None Off High Exit/Save..….......1 Host device, type Y for yes, followed by Cr. New configuration changes are storedIf you have made necessary changes to Selecting #1 will give the same results asFor For 57.6K a for 76.8K B for 115.2K Enter Request For DTR RTS Host Code User programmable. Default Port SelectPort Select Code is $BTCharacter Guard is disabled ID Echo Default Connect Port ID Echo is disabledConnect Port Header Login SetupHeader is enabled Password Default Password is BTA, disabled.Menu If enabled, the following header and menu appears Auto Connect PortSerial connection Port is disabled Escape Character ........… Answer DisabledRings to Rings to Answer isConnectivity TimeoutDefault Connectivity Timeout is MinutesCharacter Default Escape Character is 43, which isEscape 2B Hex or a plus sign +Unit ID Identifies the unit. Default Unit ID is DS71Unit Reset Or DS71-MD2Driven AsciiPort Device Name …..............................3 Selections 1-8 are fully programmable DS73TP Enter password Dial-UP Subnet Mask Default Dial-Up IP Address isDefault Subnet Mask is Primary Default Gateway address isGateway DNSSecondary Default Primary DNS address isMenu. Default Secondary DNS address is 0.0Nbns Default Primary Nbns address isDefault Secondary Nbns address is User Name Default User Name is user1Default Password is BTA Name Default Module Name is DS73TPModule Accessing Main Menu RPC OperationControlling Receptacles Outlet 1, Outlet 2, Outlet 3, Outlet Change Password DS-RPC ConfigOutlet Outlet 4 Enter Request Confirmation Enable/DisableIs Enabled RPC Technical Support Outlet DS-RPC Model DS-RPC Serial NumberModule OUTLET3 OutletCall BayTech to get a Return Authorization Number REPACKAGING, Shipping and Returning to the FactoryFCC Radio Frequency Interface Statement FCC Requirements for the DS71-MD2FCC Radio Frequency Interface Statement Table A.1 SpecificationsAppendix a Base DS71 Host DS71-MD2 DS74 Appendix B Rockwell Chip SET Modems Command Interpretation Save modem’s configuration in non-volatile memoryMake NEW Connection Appendix CMY Computer Properties DIAL-UP NetworkingPost Dial Terminal Screen Appendix D Drawings DS71 Mechanical LayoutDS71-MD2 Mechanical Layout DS74 Mechanical Layout DS73 Mechanical Layout Appendix E Ascii Character DefinitionBreak condition · Rings to Answer · 45, 46 RTS/DTR Line Driver · 29, 31 XON/XOFF ·