Bay Technical Associates DS73 Rings to Answer is, Modem to, Xon/Xoff, Disabled

Page 54

DS-RPC OWNER’S MANUAL

DETAILED OPERATION AND CONFIGURATION

__________________________________________________________________________________________

Rings to

Configure the number of rings (1 - 4) for the

Answer

modem to answer). For example, if the

 

rings to auto-answer are 3, the modem will

 

answer following the third ring. Default

 

Rings to Answer is 2.

 

 

Select #1, “Rings to Answer,” from the

 

Local Modem Setup menu, followed by

 

<cr>. The DS71-MD2 displays the current

 

setting for number of rings to auto-answer

 

and asks if you want to change:

 

Rings to Auto-Answer

2

 

Change It? (Y/N) :

 

 

Type “Y“ for yes followed by <cr>. The

 

DS71-MD2 responds:

 

 

Enter Number of Rings to Auto-Answer (1 to 4)

 

Enter the number of times you want the

 

modem to ring before it answers, followed

 

by <cr>. The DS71-MD2 stores the change

 

in non-volatile memory and returns to the

 

Local Modem Setup menu.

 

Modem to

Modem to Modem Xon/Xoff is an ASCII

Modem

Xon or Xoff character used by one modem

Xon/Xoff

signaling the other to stop or resume

 

transmitting data. Default Modem to

 

Modem Xon/Xoff handshaking is

 

disabled.

 

Select #2, “Modem to Modem Xon/Xoff,” from the Local Modem Setup menu, followed by <cr>. The DS71-MD2 displays the current Xon/Xoff status and asks if you want to enable:

46

Image 54
Contents DS-RPC Data SWITCH/POWER Control BayTech Manual Publication #U140A124-01 AugustPage Iii Page Introduction to the DS-RPC DS71-MD2 Technical Support Page Introduction to the DS-RPC Page Programmable Features of the DS Modules Feature Description ActionDS71 or DS71-MD2 Host Module Programmable Features of the DS Modules con’t Feature Description Action DS71-MD2 Host ModuleFeature Description Action DS73TP N Etwork ModuleDS-RPC Quick Start EIA-232 Serial ConnectionOperation Selecting a Device DS-RPC Module Configuration RPC Installation UnpackingPreparing the Installation Site PowerPower ON/OFF State Power UP SequenceCircuit Breaker Cabling RJ-45 Cables and AdaptersDS73TP Connection DS71 EIA-232 RJ-45 Pin/Signal Definition DS74 EIA-232 RJ-45 Pin/Signal Definition Modem Connections PIN EIA-232 Serial Detailed Operation ConfigurationConnecting to the DS-RPC ConnectionDS71-MD2 only Detailed Operation and Configuration Operation Device a Device B Device C Device D Ascii Character Menu DrivenSelection StringTerminate Binary Binary Mode$BT2,1cr$BTBcr ModePPP DIAL-UP MenuConfiguration Or this for the DS71-MD2 StatusConfiguration Serial PortDTR RTS 115.2K None Off High Exit/Save..….......1 Host device, type Y for yes, followed by Cr. New configuration changes are storedIf you have made necessary changes to Selecting #1 will give the same results asFor For 57.6K a for 76.8K B for 115.2K Enter Request For DTR RTS Host Code User programmable. Default Port SelectPort Select Code is $BTCharacter Guard is disabled Default Connect Port ID Echo is disabled Connect PortID Echo Login Setup Header is enabledHeader Password Default Password is BTA, disabled.Menu If enabled, the following header and menu appears Auto Connect PortSerial connection Port is disabled Escape Character ........… Answer DisabledRings to Rings to Answer isConnectivity TimeoutDefault Connectivity Timeout is MinutesCharacter Default Escape Character is 43, which isEscape 2B Hex or a plus sign +Unit ID Identifies the unit. Default Unit ID is DS71Unit Reset Or DS71-MD2Driven AsciiPort Device Name …..............................3 Selections 1-8 are fully programmable DS73TP Enter password Dial-UP Default Dial-Up IP Address is Default Subnet Mask isSubnet Mask Primary Default Gateway address isGateway DNSSecondary Default Primary DNS address isMenu. Default Secondary DNS address is 0.0Default Primary Nbns address is Default Secondary Nbns address isNbns Default User Name is user1 Default Password is BTAUser Name Default Module Name is DS73TP ModuleName Accessing Main Menu RPC OperationControlling Receptacles Outlet 1, Outlet 2, Outlet 3, Outlet Change Password DS-RPC ConfigOutlet Outlet 4 Enter Request Enable/Disable Is EnabledConfirmation RPC Technical Support Outlet DS-RPC Model DS-RPC Serial NumberModule OUTLET3 OutletCall BayTech to get a Return Authorization Number REPACKAGING, Shipping and Returning to the FactoryFCC Radio Frequency Interface Statement FCC Requirements for the DS71-MD2FCC Radio Frequency Interface Statement Specifications Appendix aTable A.1 Base DS71 Host DS71-MD2 DS74 Appendix B Rockwell Chip SET Modems Command Interpretation Save modem’s configuration in non-volatile memoryAppendix C MY ComputerMake NEW Connection Properties DIAL-UP NetworkingPost Dial Terminal Screen Appendix D Drawings DS71 Mechanical LayoutDS71-MD2 Mechanical Layout DS74 Mechanical Layout DS73 Mechanical Layout Appendix E Ascii Character DefinitionBreak condition · Rings to Answer · 45, 46 RTS/DTR Line Driver · 29, 31 XON/XOFF ·