Bay Technical Associates DS2-RPC, DS4-RPC, DS73, DS2-RPC DS4-RPC owner manual Configuration

Page 34

DS-RPC OWNER’S MANUAL

DETAILED OPERATION AND CONFIGURATION

__________________________________________________________________________________________

CONFIGURATION

DS71 OR DS71-MD2If you are using the Menu Selection Method,

CONFIGURATION select C, “Configure,” followed by <cr> from the DS-RPC Main Menu. The following selection menu appears:

Configuration
Module 1	1
Module 2	2
Module 3	3
Select Port	S
Exit	X
Enter Request :

If you are using the ASCII Character String Method, exit main menu, then select the module to configure. To select Module #1, type $BT1<cr>. The DS71 or DS71-MD2 responds “Requested Connection Made.” Send the ASCII configuration command $CONFIG. The configuration menu appears.

Enter the number of the module to configure, followed by <cr>. To configure the host module 1, select #1. The following configuration menu appears for the DS71:

Copyright(C) Bay Technical Associates 1998

DS71 Data Switch Series - Host Module

Revision F.2.01

Module 1

Status.....................…………..….......1

Serial Port Configuration...……......2

Port Device Name..............………....3

Port Select Code..............…………..4

Attention Character.........……….....5

Disconnect Timeguard.....……….....6

Connect Port ID Echo....……….......7

Login Setup....................……………8

DCD Logon/Logoff.......……….........9

Unit ID........................……………...U

Configure Another Module.....….....C

Exit...........................………………...X

26

Image 34

Contents DS-RPC Data SWITCH/POWER Control BayTech Manual Publication #U140A124-01 AugustPage Iii Page Introduction to the DS-RPC DS71-MD2 Technical Support Page Introduction to the DS-RPC Page Feature Description Action Programmable Features of the DS ModulesDS71 or DS71-MD2 Host Module Programmable Features of the DS Modules con’t Feature Description Action DS71-MD2 Host ModuleFeature Description Action DS73TP N Etwork ModuleEIA-232 Serial Connection DS-RPC Quick StartOperation Selecting a Device DS-RPC Module Configuration RPC Installation UnpackingPreparing the Installation Site PowerPower UP Sequence Power ON/OFF StateCircuit Breaker RJ-45 Cables and Adapters CablingDS73TP Connection DS71 EIA-232 RJ-45 Pin/Signal Definition DS74 EIA-232 RJ-45 Pin/Signal Definition Modem Connections PIN EIA-232 Serial Detailed Operation ConfigurationConnecting to the DS-RPC ConnectionDS71-MD2 only Detailed Operation and Configuration Operation Device a Device B Device C Device D Ascii Character Menu DrivenSelection StringTerminate Binary Binary Mode$BT2,1cr$BTBcr ModePPP DIAL-UP MenuConfiguration Or this for the DS71-MD2 StatusConfiguration Serial PortDTR RTS 115.2K None Off High Exit/Save..….......1 Host device, type Y for yes, followed by Cr. New configuration changes are storedIf you have made necessary changes to Selecting #1 will give the same results asFor For 57.6K a for 76.8K B for 115.2K Enter Request For DTR RTS Host Code User programmable. Default Port SelectPort Select Code is $BTCharacter Guard is disabled Connect Port Default Connect Port ID Echo is disabledID Echo Header is enabled Login SetupHeader Password Default Password is BTA, disabled.Menu If enabled, the following header and menu appears Auto Connect PortSerial connection Port is disabled Escape Character ........… Answer DisabledRings to Rings to Answer isConnectivity TimeoutDefault Connectivity Timeout is MinutesCharacter Default Escape Character is 43, which isEscape 2B Hex or a plus sign +Unit ID Identifies the unit. Default Unit ID is DS71Unit Reset Or DS71-MD2Driven AsciiPort Device Name …..............................3 Selections 1-8 are fully programmable DS73TP Enter password Dial-UP Default Subnet Mask is Default Dial-Up IP Address isSubnet Mask Primary Default Gateway address isGateway DNSSecondary Default Primary DNS address isMenu. Default Secondary DNS address is 0.0Default Secondary Nbns address is Default Primary Nbns address isNbns Default Password is BTA Default User Name is user1User Name Module Default Module Name is DS73TPName Accessing Main Menu RPC OperationControlling Receptacles Outlet 1, Outlet 2, Outlet 3, Outlet Change Password DS-RPC ConfigOutlet Outlet 4 Enter Request Is Enabled Enable/DisableConfirmation RPC Technical Support Outlet DS-RPC Model DS-RPC Serial NumberModule OUTLET3 OutletCall BayTech to get a Return Authorization Number REPACKAGING, Shipping and Returning to the FactoryFCC Radio Frequency Interface Statement FCC Requirements for the DS71-MD2FCC Radio Frequency Interface Statement Appendix a SpecificationsTable A.1 Base DS71 Host DS71-MD2 DS74 Appendix B Rockwell Chip SET Modems Command Interpretation Save modem’s configuration in non-volatile memoryMY Computer Appendix CMake NEW Connection Properties DIAL-UP NetworkingPost Dial Terminal Screen Appendix D Drawings DS71 Mechanical LayoutDS71-MD2 Mechanical Layout DS74 Mechanical Layout DS73 Mechanical Layout Appendix E Ascii Character DefinitionBreak condition · Rings to Answer · 45, 46 RTS/DTR Line Driver · 29, 31 XON/XOFF ·