Avery ALS 330/430 manual Applicator modes, Signals for direct dispense

Page 64

Operators Manual

ALS 330/430

8.2 Applicator modes

The machine is able to dispense the label direct on the passing product. There is also the possibility to drive without any external control a wide range of applicators.

8.2.1Signals for direct dispense

For direct dispensing the airstream signal can be used to control a pneumatic driven dispensing edge. The start of the airstream signal (= motor run signal) could be behind the start of the dispense motor, adjusted with the function APT3. The signal is switched inactive, when the label dispense has been completed. Also the stop could be adjusted with the function ASTP to switch inactive before or behind the dispense motor stop.

Ready

Product start

Label start Suppression

1

4

3

Product start Suppression

Dispense

Motor run signal

PRDL

 

POS

 

 

 

 

POS

 

POS

 

 

 

2

 

 

APT3

ASTP

ASTP

 

 

 

1Productstart disabled. PRDL activ

2Missing Label: New start of dispense during dispenser activ

3Inhibit activ

4Machine not ready. Errorcondition or not online

Figure 17 Timing diagram direct dispense

Release 4/06

Page 56

Connections and signals

Image 64
Contents Page Page ALS 330/430 Menu structure Errors and warnings ALS 330/430 Important Notes OverviewManufacturer CopyrightSafety General Safety NotesOperator’s duty of care Concrete security regulations and symbols used Security measures during maintenance and repairs Security measures during normal operationWork on pneumatic equipment Work on the electrical equipmentObserve environmental regulations Description MechanicsMachine layout Operator panel Operator panelPlug board Plug boardElectronics ALS 330/430 Preparing the machine InstallationPrepare dispensing Define label data Setting Lpit manually Manual adjustment of the Cont parameterCapacitive label sensor Capacitive sensorLabel guide Adjust dispense functionStop position Fixed dispensing speed Automatic dispensing speed ApsfLabel position on the product Product data bankSafety recommendation OperationInserting label material Left hand version Right hand versionRemoving label material Mounting a new label rollMounting a new label roll on ALS 330 Euro Mounting a new label roll on ALSAdjusting the pressure roller RewindAdjustment of the dispensing edge Lead screw adjustmentPrinter adjustment Adjust pressure roller Initializing new label materialFunction Display message Mains switch Control of dispense unitDispenser Menu selection Missing label function and web breaksDispenser active on Display and data inputDisplay Menu function Function data value Material initialisation Init Dispenser stopped OFFLabel position POS Stop position Stod Start delaySTADDispense speed Velo Blow on time Blow MaintenanceProduct menu PD0n Release 4/06 Operation Page Configuration menu Menu structureStandard menu Extended standard menuConfiguration Standard menu  DirectApplicator Extended menuInitialisation Init Standard menuDisplay Function Values Labelling time Blow Start delay StadDispensing speed Velo Extended standard menu Display Function Data valueLabel contrast Label pitch LpitSensor status Sens Product length Prdl Label positionPOSElectronic gear ratio adjustment Egra Egra value check StstSlew speed Slew Dwell time APT1Blow on time APT2 Restart delay APT3Time constant compensation APT4 End of air stream signal Astp Printer dwell time PDTSave parameter in data bank Save Load data bank LoadProduct menu Page Configuration menu Possible adjustmentsCalling the configuration menu Possible testsHandling the menu Display Function of the parameter Possible data entryMenu functions Automatic product speed followerAPSF Type of applicator ApplOutput check OCH Input and sensor check ICHAdditional functions in the standard menu Adjustment resettingFACT Interface baud rate BaudParity bit Pari Number of stop bits SbitNumber of data bits Dbit Recycle simulates max labels/min RecyDistance sensor to dispensing edge Dist Label counter LabcLeave Menu finishing Quit Dispenser connector Signal description Pol D Serial interfaceData of the serial interface Direction Code Description 25 pol Pol SubCommand Description Range Interface commandsExample Ledg Message in display Connections and signals Output signalsSignals for direct dispense Applicator modesControl signals for the ASA applicator Timing ASA applicatorSignals for the EP applicator APT2Applicator connector Applicator connectorInput signals Connecting NPN left or PNP right inputsExample for connecting an NPN sensor Datalogic Product sensorOD Control sensor NPN connection of optional ODC sensorApsf sensor Connection of a NPN type Apsf sensorControl signals Optional connector for process controInternal I/O connector EMI RuleElectronic diagrams Wiring diagram Layout dispenser electronic board Resolution ALS 330/430 Page Errors and warnings Dispenser error messagesSTO! Power-fail message Message Meaning How to solveInto Dispenser warnings EepromALS 330/430 Technical Information Technical specificationDescription Details 330 430 Application specification APSF- Sensor Specification Optional functionPerformance charts ChartsPerformance chart Ramp Norm Deceleration Labels/min 900 25 mm 50 mm 75 mm 800 ALS 330/430 Page Adjustment Function Factory ApplicationFunction Factory PD01 PD02 PD03 PD04 Function PD05 PD06 PD07 PD08 PD09Index