Toshiba 555, 855, 755, 655 Hardware Problems, „ Startup page not printed, „ Print jobs not output

Page 63

3 TROUBLESHOOTING FOR PRINTING

Hardware Problems

This section describes troubles caused by the hardware device (the equipment).

If an icon or a message indicating an error is not displayed, or the problems on printer drivers or the network connection cannot be specified, a hardware problem is a possible cause of the trouble.

The following are common factors involved in the hardware problems:

ySystem board, cables, and connectors

yThe equipment, and its (optional) components such as the duplexing unit or the Finisher

ySystem software or firmware of the equipment

„Startup page not printed

Problem Description

If the startup page is not printed when you turn on the equipment, even though the Print Startup Page is enabled, there may be a hardware error. Contact your service representative.

Corrective Action

1.Make sure that Print Startup Page is enabled.

2.Turn on the equipment. (If it is already on, restart it.)

3.Check if the startup page is output.

When the Print Startup Page is enabled, normally the Startup Page is automatically printed. If not, the problem is possibly caused by the hardware. Contact your service representative.

„Print jobs not output

Problem Description

All the clients within a network fail to make the equipment output the print jobs.

Corrective Action

There remains a possibility that an improper settings of the software such as printer drivers caused the problem, however, a hardware error is possible, if none of the clients can print the jobs. Try the steps on the checklist below. If the problem persists after you have followed all of the steps, contact your service representative.

No

Check...

Yes

No

Corrective Action

 

 

 

 

 

1

Is printing prohibited from all connected client

Next Step

Ö

See the following section to fix the problem:

 

computers?

Ø

P.59

“Network Connection Problems”

 

 

 

 

 

 

 

2

Can you see the job from TopAccess or another

Next Step

 

See the following section to fix the problem:

 

print monitoring utility, such as PCONSOLE or

Ö

P.70

“Locating the Equipment in the Network”

 

Ø

 

Print Manager?

 

 

 

 

 

 

 

 

 

 

 

 

 

3

Can you identify the problem with the error

 

 

See the following sections to fix the problem:

 

message or the error code and resolve it?

End

Ö

P.82

“Error Messages”

 

 

 

 

P.86

“Error Codes”

 

 

 

 

 

 

Also refer to the Printing Guide for more information on resolving output errors caused by software settings.

Hardware Problems 61

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Troubleshooting Guide Page ‰ Trademarks „ How to read this manual ‰ Symbols in this manualPreface ‰ ScreensPage Contents Troubleshooting for Scanning Regular Maintenance Contents Replacing a Toner Cartridge Cleaning the Hole Punch Dust BinClearing a Paper Jam Clearing a Staple JamMessages Displayed on the Touch Panel Message Problem Description Corrective ActionChange Drawer to Correct Error Codes „ Locating a paper jam Clearing a Paper JamAfter clearing the jam, close all the opened covers „ Clearing a paper jam‰ Tips on removing the jammed paper Clear the paper jam„ Paper jam in the Reversing Automatic Document Feeder Lower ‰ If paper jams occur frequentlyClose the Reversing Automatic Document Feeder „ Paper jam in the Reversing Automatic Document Feeder UpperLower the original feeder tray Close the upper cover „ Paper jam in the bypass trayClose the transport guide Under the guide plate„ Paper jam in the External Large Capacity Feeder optional Separate the finisher from the equipment Clearing a Paper Jam Clearing a Paper Jam Clearing a Paper Jam Clearing a Paper Jam Open the paper feed cover „ Paper jam inside of the equipmentConnect it with the equipment It could burn or injure you Open the fuser unit cover „ Clearing paper jams caused by a wrong paper size setting Presspanel. the User Functions button on the control ‰ Jam when making copies or prints using a drawerClearing a Paper Jam ‰ Jam when making copies or prints using the bypass tray ‰ Jam when printing from the FAXTurn off the main power switch Drawer button on the touch panel Remove any jammed staples with something sharp Clearing a Staple JamClose the front cover of the finisher „ Staple jam in the Saddle Stitch Finisher MJ-1029Lower the guide while holding the knob „ Staple jam in the saddle stitch unit Fit the staple cartridges Remove the jammed staplesClearing a Staple Jam Replacing a Toner Cartridge Replacing a Toner CartridgeShakeinside.the new toner cartridge well to loosen the toner Toner supplying operation automatically starts „ Replacing a Near Empty toner cartridge See Refilling With Staples „ Refilling Saddle Stitch Finisher MJ-1029 staples Refilling With Staples „ Refilling saddle stitch unit staples Close the lower cover of the Saddle Stitch Finisher Fit the new cartridgesCleaning the Hole Punch Dust Bin Page Copying Problems Troubleshooting for CopyingProblem Description Cause Corrective Action Copying ProblemsCopying Problems Page Client Problems Print Job ProblemsPrinter Driver Problems Network Connection Problems„ Clearing print job errors Print Job ProblemsTo print by setting suitable-size paper in the drawer Problem Description „ Retrieval of printer configuration failed Printer Driver Problems„ Cannot print port setting problems „ Command line options not processed„ Cannot print a job as expected using PS3 printer driver Network Connection Problems „ Cannot print with SMB print„ Cannot print properly with AppleTalk print „ Checking the client status Client ProblemsHardware Problems „ Startup page not printed„ Print jobs not output Page Scanning Problems Troubleshooting for ScanningScanning Problems „ Cannot E-mail my scans„ Cannot find the data saved in the shared folder Filing Web Utility Problems Troubleshooting for e-FilingFiling Web Utility Problems „ e-Filing Web Utility terminates the session„ Numerous sub windows repeatedly appear Message Corrective Action „ Error messagesFiling Web Utility Problems Locating the Equipment in the Network Ldap Search and Authentication ProblemsPrinting Problems Network Related Network Fax N/W-Fax Driver Problems„ Cannot locate the equipment in the network Locating the Equipment in the Network„ Cannot locate the equipment with Local Discovery Check the network settings following the checklist below „ Equipment does not respond to ping command„ Ldap authentication takes a long time Ldap Search and Authentication ProblemsPrinting Problems Network Related „ Novell print in a NetWare environment „ IPP print in a Windows operating system environment„ UNIX/Linux environment „ Macintosh environmentNetwork Fax N/W-Fax Driver Problems ‰ Problem with the current printer setup ‰ This port is currently in use‰ Fax transmission cannot be performed with a cover sheet Checking the Equipment Status Error Messages Error CodesPrinter Error Hardware Status Icons on TopAccess Device TabPaper Empty TopAccess Message Corrective Action Error MessagesDocuments in the Scan folder have been deleted by a user MFP Error Messages „ Error codes on print jobs Error CodesA2A1 „ Error codes on transmission and reception Device name 3D20 „ Error codes on scan jobs Save as File Store to e-Filing Perform the print with the administrator’s password. If Regular Maintenance When You Think Something Is Wrong With the Equipment„ General operations When You Think Something Is Wrong With the EquipmentGuide „ Originals and paperScanning area surface of the long rectangular glass Regular MaintenanceIndex User information DP-5550/6550/7550/8550 OME08016900 Multifunctional Digital Systems
Top Page Image Contents