Xilinx ML605 manual Voltage Rails, 2Virtex-6 Fpga Configuration Modes M20, Cclk Direction

Page 14

Chapter 1: ML605 Evaluation Board

The ML605 supports Master BPI-Up, JTAG, and Slave SelectMAP. These are selected by setting M[2:0] options 010, 101 and 110 shown in Table 1-2.

Table 1-2:Virtex-6 FPGA Configuration Modes

Configuration Mode	M[2:0]	Bus Width(1)	CCLK Direction
Master Serial(2)	000	1	Output
Master SPI(2)	001	1	Output
Master BPI-Up(2)	010	8, 16	Output
Master BPI-Down(2)	011	8, 16	Output
Master SelectMAP(2)	100	8, 16	Output
JTAG	101	1	Input (TCK)

Slave SelectMAP	110	8, 16, 32	Input

Slave Serial(3)	111	1	Input

Notes:

1.The parallel configuration modes bus is auto-detected by the configuration logic.

2.In Master configuration mode, the CCLK pin is the clock source for the Virtex-6 FPGA internal configuration logic. The Virtex-6 FPGA CCLK output pin must be free from reflections to avoid double-clocking the internal configuration logic. See the Virtex-6 FPGA Configuration User Guide for more details. [Ref 5]

3.This is the default setting due to internal pull-up termination on mode pins.

For an overview on configuring the FPGA, see “Configuration Options,” page 73.

Note: The mode switches are part of DIP switch S2. The default mode setting (see Table A-1, page 75) is M[2:0]=010, which selects Master BPI-Up at board power-on. Switch S1 position 4 must be OFF to disable the System ACE controller from attempting to boot if a CF card is present.

References

See the Virtex-6 FPGA Configuration User Guide for detailed configuration information. [Ref 5]

I/O Voltage Rails

There are 16 I/O banks available on the Virtex-6 device. The voltage applied to the FPGA I/O banks used by the ML605 board is summarized in Table 1-3.

Table 1-3:Voltage Rails

	U1 FPGA Bank	I/O Rail	Voltage

	Bank 0	VCC2V5_FPGA	2.5V

	Bank 12(1)	FMC_VIO_B_M2C	2.5V
	Bank 13	VCC2V5_FPGA	2.5V

	Bank 14	VCC2V5_FPGA	2.5V

	Bank 15	VCC2V5_FPGA	2.5V

	Bank 16	VCC2V5_FPGA	2.5V

	Bank 22	VCC2V5_FPGA	2.5V

	Bank 23	VCC2V5_FPGA	2.5V


14		www.xilinx.com	ML605 Hardware User Guide
			UG534 (v1.2.1) January 21, 2010

Image 14

Contents ML605 Hardware User Guide UG534 v1.2.1 January 21, 2010 optionalRevision History Date Version RevisionTable of Contents ML605 Hardware User Guide About This Guide Additional Support Resources Preface About This GuideML605 Evaluation Board Additional InformationSMA FeaturesML605 Evaluation Board IIC Eeprom 1 KBOverview Fpga Init Fpga DoneBlock Diagram 1ML605 High-Level Block DiagramDetailed Description ML605 FeaturesFeature DDR3 SodimmWDW6TP ML605 Evaluation Board ML605 Features Cont’dSgmii Configuration Virtex-6 XC6VLX240T-1FFG1156 FpgaCclk Direction 2Virtex-6 Fpga Configuration Modes M20Voltage Rails 3Voltage Rails U1 Fpga BankVCC1V5FPGA MB DDR3 Memory SodimmDetailed Description 3Voltage Rails Cont’d U1 Fpga Bank 4DDR3 Sodimm ConnectionsML605 Evaluation Board 4DDR3 Sodimm Connections Cont’d DDR3A9DDR3D30 DQ30 DDR3DM0 See the Micron Technology, Inc. for more information Ref Mb Platform Flash XL MB Linear BPI FlashML605 Flash Boot Options FLASHD2 DQ2 FLASHD0 DQ0FLASHD1 DQ1 FLASHD3 DQ3Fpga Design Considerations for the Configuration Flash System ACE CF and CompactFlash Connector 6System ACE CF Connections U1 Fpga Pin Schematic Net Name USB Jtag Oscillator Socket Single-Ended Clock GenerationOscillator Differential 7ML605 Oscillator Socket Pin 1 Location Identifiers SMA Connectors Differential 8ML605 Oscillator Pin 1 Location IdentifiersSmarefclkp SMA PinSmarefclkn Multi-Gigabit Transceivers GTX MGTs ICSPCI Express Endpoint Connectivity 12PCIe Lane Size Select Jumper J428PCIe Edge Connector Connections PCIE100MMGT0P AA3 PCIERX7PAA4 PCIERX7N GTXE1X0Y6SFP Module Connector 11 /100/1000 Tri-Speed Ethernet PHY 11PHY Default Interface Mode Jumper Settings J66 J67 J6812Board Connections for PHY Configuration Pins Bit2 Bit1 Bit013Ethernet PHYConnections U1 Fpga Pin 12Board Connections for PHY Configuration Pins Cont’dSgmii GTX Transceiver Clock Generation U80 M88E1111PHYRXD5 PHYRXD4RXD4 RXD5Ground USB-to-UART BridgeVbus U81 USB Controller USB Controller16USB Controller Connections U38 Chrontel CH7301C DVI Codec17DVI Controller Connections IIC Bus 14IIC Bus Topology Iicsclmain SCL Kb NV MemoryIicsdamain SDA Designator Signal Name Color Label Description Status LEDsEthernet PHY Status LEDs 16Ethernet PHY Status LEDsControlled LED User I/OFpga Init and Done LEDs Fpgainitb18User LEDs and Gpio Connector, Directional LEDs User LEDsGpio J62 Pin Controlled LED User Pushbutton SwitchesDetailed Description 21User LED Connections Fpga U1 Pin User DIP Switch Switch PinUsersmagpiop User SMA GpioUsersmagpion LCD Display 16 Character x 2 Lines J41 PinSwitches Power On/Off Slide Switch SW2Sysaceresetb Pushbutton SW3 Active-Low Fpgaprogb Pushbutton SW4 Active-LowSystem ACE CF CompactFlash Image Select DIP Switch S1 26System ACE CF CompactFlash Image Select DIP Switch S126ML605 Configuration Modes M20 Bus WidthVita 57.1 FMC HPC Connector Master BPI28VITA 57.1 FMC HPC Connections HPC Pin28VITA 57.1 FMC HPC Connections Cont’d FMCHPCHB13P FMCHPCHB09NFMCHPCHB08P FMCHPCHB08NDetailed Description 28VITA 57.1 FMC HPC Connections Cont’d VREFAM2C Vadj VadjVIOBM2C Vadj VREFBM2CVita 57.1 FMC LPC Connector 30VITA 57.1 FMC LPC Connections LPC PinDetailed Description 30VITA 57.1 FMC LPC Connections Cont’d Power ManagementAC Adapter and Input Power Jack/Switch Onboard Power Regulation 28ML605 Onboard Power RegulatorsVccaux UCD9240PFCVccintfpga UCD7230RGWRSystem Monitor 29System Monitor External ReferenceSystem Monitor Header J35 12V Supply Monitor Fan Controller Bank Configuration Options Configuration OptionsML605 Evaluation Board Table A-1Default Switch Settings Function/Type DefaultGmii Vita 57.1 FMC LPC J63 and HPC J64 Connector Pinout Figure B-2FMC HPC Connector Pinout ML605 Master UCF Appendix C ML605 Master UCF NET DDR3D9NET DDR3DQS0P NET FLASHA21 ML605 Hardware User Guide UG534 v1.2.1 January 21 NET FMCHPCHB03P NET FMCHPCLA16N NET FMCLPCPRSNTM2CL NET Iicsdadvi NET PCIERX2N NET Pmbusdatals NET Sfplos NET Sfprxn NET Sfprxp NET USBD6LS References Appendix D References