Epson G3 Series manual General Maintenance, Schedule for Maintenance Inspection

Page 78

Maintenance 1. Safety Maintenance

CAUTION

Be sure to connect the cables properly. Do not allow unnecessary strain on the cables. (Do not put heavy objects on the cables. Do not bend or pull the cables forcibly.) The unnecessary strain on the cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system.

2.General Maintenance

This chapter describes maintenance inspections and procedures. Performing maintenance inspections and procedures properly is essential for preventing trouble and ensuring safety. Be sure to perform the maintenance inspections in accordance with the schedule.

2.1 Schedule for Maintenance Inspection

Inspection points are divided into five stages: daily, monthly, quarterly, biannual, and annual. The inspection points are added every stage.

If the Manipulator is operated for 250 hours or longer per month, the inspection points must be added every 250 hours, 750 hours, 1500 hours, and 3000 hours operation.

 

 

 

 

Inspection Point

 

 

 

 

Daily

Monthly

 

Quarterly

 

Biannual

Annual

 

 

inspection

inspection

 

inspection

 

inspection

inspection

1 month

(250 h)

 

 

 

 

 

 

2 months

(500 h)

 

 

 

 

 

 

3 months

(750 h)

 

 

 

 

 

4 months

(1000 h)

 

 

 

 

 

 

5 months

(1250 h)

Inspect

 

 

 

 

 

6 months

(1500 h)

 

 

 

 

 

 

 

7 months

(1750 h)

every

 

 

 

 

 

 

 

 

 

 

 

8 months

(2000 h)

day

 

 

 

 

 

9 months

(2250 h)

 

 

 

 

 

 

 

 

 

10 months

(2500 h)

 

 

 

 

 

 

11 months

(2750 h)

 

 

 

 

 

 

12 months

(3000 h)

 

 

 

13 months

(3250 h)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

h = hour

68

G3 Rev.1

Image 78
Contents G3 series Manipulator Manual G3 series Manipulator Manual Foreword Service Center Japan & Others North & South America Epson AMERICA, INCEurope Before Reading This Manual Controller RC180 Software Epson RC+ 5.0 Ver .3 or greaterG3 Rev.1 Table of Contents Motion Range Safety Maintenance General MaintenanceMaintenance Parts List CoversSetup & Operation Page Safety Setup & Operation 1. SafetyConventions Design and Installation Safety Operation Safety All necessary safety precautionsUnexpectedly Emergency Stop Free running distance in emergencyEmergency Movement Without Drive Power Joint #4Manipulator Labels Be careful not to burn yourselfCommon Multiple Mounting Table Top Mounting Setup & Operation 2. Specifications SpecificationsFeatures of G3 series Manipulators Space productivityModel Number and Model Differences Part Names and Outer Dimensions Table Top MountingStandard-model G3-***S Or more Setup & Operation 2. Specifications Cleanroom-model G3-***C Reference through hole View from the bottom of the base Multiple Mounting Standard-model G3-***1SMG3-301SM G3-351SM 220 Max.410 Max.450 Upper bellows Exhaust port Plate cover Lower bellows Reference through hole View from the bottom of the base Specifications Assignable Value How to Set the Model Environmental Conditions Environments and InstallationSetup & Operation 3. Environments and Installation ConditionsBase Table Do not remove the M/C cables from the ManipulatorMounting Dimensions Space for teaching Space for maintenance and inspectionSpace for cables G3-251S/C Standard G3-301S/C G3-301SM/CM Unpacking and Transportation Installation Procedure Multiple Mounting Connecting the Cables Cleanroom-modelCable Connections Pneumatic Tubes User Wires and Pneumatic TubesElectrical Wires Malfunction of the robot systemMultiple Mounting Precautions for Relocation and Storage Relocation and StorageTable Top Mounting Example of Arm Retaining Posture Wire tie Sheet Setting of End Effectors Attaching an End EffectorCommon Dimensions Table Top Mounting Attaching Cameras and ValvesUnit mm Equivalent Weight Formula Weight and Inertia SettingsWeight Setting Load on the ShaftAutomatic speed setting by Weight 140 Automatic acceleration/deceleration setting by Weight 120100 Moment of inertia of load on the shaft Inertia SettingMoment of Inertia and the Inertia Setting 100 005Eccentric Quantity Eccentric quantity of load on the shaft100 150 Moment of inertia of a rectangular parallelepiped Moment of inertia of a cylinder100 120 150 Precautions for Auto Acceleration/Deceleration of Joint #3Automatic acceleration/deceleration vs. Joint #3 position Mm Shaft height G3 Rev.1Setup & Operation 5. Motion Range Motion RangeMotion Range Setting by Pulse Range for All Joints 1 Max. Pulse Range of Joint #1 2 Max. Pulse Range of Joint #2 ±142 / ±1423 Max. Pulse Range of Joint #3 4 Max. Pulse Range of Joint #4Motion Range Setting by Mechanical Stops Setting the Mechanical Stops of Joints #1 and #2 Views from the bottom of Arm #1Views from the top of Arm #1 G3-**1SM/CM-RJoint RecommendedSetting the Mechanical Stop of Joint #3 Sets low speed Standard Motion Range G3-251S 141 79.3 84.0 120 250 221.9 224.5 G3-301S-L 150 G3-301S-R G3-301SM/CM 115 G3-351SM-L G3-351SM-R 105 130 120 Setup & Operation 5. Motion Range Maintenance Page Not connect it directly to a factory power source Safety MaintenanceMaintenance 1. Safety Maintenance StoppedGeneral Maintenance Schedule for Maintenance InspectionInspection While the Power is on Manipulator is operating Maintenance 2. General MaintenanceInspection Point Greasing Bolt Tightening Torque Tightening Hexagon Socket Head Cap BoltsMatching Origins Set Screw Tightening TorqueLayout of Maintenance Parts G3-**1C Cleanroom-model with bellowsG3-**1S Standard-model G3-**1CM Cleanroom-model with bellows G3-**1SM Standard-modelR13B031226 Maintenance 3. CoversCovers R13B031227Arm Top Cover Table Top Mounting Multiple MountingRemoval Installation G3-**1S* Standard-model Arm Bottom CoverArm Cap G3-**1 Table Top MountingConnector Plate G3-**1* Table Top Mounting G3-**1*W Multiple MountingUser Plate Connector Sub PlateG3-**1S* Standard-model G3-**1C* Cleanroom-model G3-**1* Table Top MountingHeatsink Plate Base Bottom CoverMaintenance Parts List Maintenance 4. Maintenance Parts ListCommon Parts Parts by Environment Model Standard-model