Teledyne 4060 manual Maintenance & Troubleshooting

Page 11

Series 4060

4.5 Sample Pump	44
4.6 Analyzer Operation	44
4.6.1 Default Parameters	46
4.6.2 Style Conventions	46
4.6.3 Navigation and Data Entry	47
4.6.3.1 Arrow Keys	47
4.6.3.2 ENTER	47
4.6.3.3 ESCAPE	48
4.6.4 Menu Structure	48
4.6.4.1 Main Menus	49
4.6.5 Span	50
4.6.6 ALT-SPAN	51
4.6.7 The Model Screen	51
4.6.8 System Self-Diagnostic Test	51
4.6.9 The Alarms Function	52
4.6.10 The Range Function	55
4.6.11 Analog Output Adjustment	55
4.6.12 Linearization	56
4.6.13 Changing Stream	56
4.6.14 Setting up an AUTO-CAL	56
4.6.15 Timing	58
4.6.16 Group Setup	58
4.6.17 Password Protection	58
4.6.18 Logging Out	61
4.6.19 Standby	62
Maintenance & Troubleshooting................................................ 65
5.1 Measuring Circuit Electrical Checks	66
5.1.1 Anode Voltage Check	66
5.1.2 Electronic Stability	67
5.1.3 Printed Circuit Board Replacement	67

Teledyne Analytical Instruments

xi

Image 11

Contents Series Teledyne Analytical Instruments SeriesTeledyne Analytical Instruments Iii Safety MessagesSeries Combustible GAS Usage Additional Safety InformationSeries Teledyne Analytical Instruments Vii Procedure for Removal of Internal Inaccessible Shock HazardsViii Table of Contents Operation Maintenance & Troubleshooting Appendix B AppendixTeledyne Analytical Instruments Xiii List of FiguresList of Tables Series Introduction Main Features of the AnalyzerIntroduction Introduction Series Principle of OperationAnalyzer Description Model 4060 Front Panel Interface Applications Series Operational Theory Operational TheoryIntroduction Modes of OperationSample System Analyzer SubsystemsOperational Theory Series Gas Flow Control System Internal Temperature ControllersFlame Ionization Detection Cell Fuel and Blanket Air SystemsTypical Piping Diagram for the Model Detection Cell Flame Ionization Cell Electrometer-AmplifierFlame Ignition Circuit Anode Power SupplyFlame Guard Circuit Mounting the Analyzer InstallationSeries Installation Unpacking the AnalyzerElectronic Connections Installation SeriesElectrical Power Connections User ConnectionsModel 4060 Rear Panel with Optional Gas Manifold Equipment Interface Connector Pin Arrangement Pin Function Threshold Alarm System Alarm Remote Calibration Connections Range ID Relay Connections 2.10 RS-232 Port Pin out of 50 pin D-Sub ConnectorGas Connections Commands via RS-232 InputGas Connections Less than 0.5 PPM Placing the System in Operation Series Operation OperationEquipment Operation Series Preliminary Power-Off Check ListActivating the Support Gases Span Gas Flame Ignition1 Air Carrier GasIgnition and/or Flame Guard Circuit Failure Sample PumpAnalyzer Operation Verification of the Flame Guard CircuitSeries Operation Style Conventions Default ParametersEnter Navigation and Data EntryMenu Structure EscapeMain Menus Span Model Screen System Self-Diagnostic TestALT-SPAN Alarms Function AL-1 Defeated AL-1 High AL-1 NON-FAILSAFE AL-1 NON-LATCHING Operation Series Range Function Analog Output AdjustmentChanging Stream Setting up an AUTO-CALLinearization Autocal Password Timing Group SetupPassword Protection Entering a Password Enter NEW Password Screen Logging Out Repeat Password Entry ScreenStandby Series Operation Operation Series Teledyne Analytical Instruments Series Maintenance Maintenance & TroubleshootingAnode Voltage Check Maintenance SeriesMeasuring Circuit Electrical Checks Electronic Stability Printed Circuit Board ReplacementCollector Cable Temperature Control Electronic CheckIgnition and/or Flame Guard Circuit Checks Sampling System Printed Circuit Board Descriptions Flame Guard and Anode Power Supply PCBProportional Temperature Controller PCB Electrometer-Amplifier PCB Maintenance Series Series Appendix Specifications and Initial SettingsAppendix Analytical Instruments Recommended Spare Parts ListAppendix Series PC Board Assemblies Drawing ListAppendix Series Teledyne Analytical Instruments Appendix B B1 Addendum and Testing Results