Teledyne 4060 manual Table of Contents

Page 9

Series 4060

Table of Contents

 

Safety Messages

iii

Additional Safety Information

v

List of Figures

xiii

List of Tables

xiv

Introduction

15

1.1

Main Features of the Analyzer

15

1.2

Principle of Operation

16

1.3

Analyzer Description

16

1.4

Applications

18

Operational Theory

19

2.1

Introduction

19

2.2

Modes of Operation

19

2.3

Analyzer Subsystems

20

 

2.3.1 Sample System

20

 

2.3.2 Gas Flow Control System

21

 

2.3.3 Fuel and Blanket Air Systems

22

 

2.3.4 Flame Ionization Detection Cell

22

2.4

Detection Cell

24

 

2.4.1 Electrometer-Amplifier

25

 

2.4.2 Anode Power Supply

26

 

2.4.3 Flame Guard Circuit

26

 

2.4.4 Flame Ignition Circuit

26

Installation

27

3.1

Unpacking the Analyzer

27

3.2

Mounting the Analyzer

27

 

Teledyne Analytical Instruments

ix

Image 9
Contents Series Teledyne Analytical Instruments SeriesTeledyne Analytical Instruments Iii Safety MessagesSeries Combustible GAS Usage Additional Safety InformationSeries Teledyne Analytical Instruments Vii Procedure for Removal of Internal Inaccessible Shock HazardsViii Table of Contents Operation Maintenance & Troubleshooting Appendix B AppendixTeledyne Analytical Instruments Xiii List of FiguresList of Tables Main Features of the Analyzer IntroductionSeries Introduction Principle of Operation Analyzer DescriptionIntroduction Series Model 4060 Front Panel Interface Applications Introduction Operational TheoryModes of Operation Series Operational TheoryAnalyzer Subsystems Operational Theory SeriesSample System Gas Flow Control System Internal Temperature ControllersFlame Ionization Detection Cell Fuel and Blanket Air SystemsTypical Piping Diagram for the Model Detection Cell Flame Ionization Cell Electrometer-AmplifierAnode Power Supply Flame Guard CircuitFlame Ignition Circuit Series Installation InstallationUnpacking the Analyzer Mounting the AnalyzerElectrical Power Connections Installation SeriesUser Connections Electronic ConnectionsModel 4060 Rear Panel with Optional Gas Manifold Equipment Interface Connector Pin Arrangement Pin Function Threshold Alarm System Alarm Remote Calibration Connections Range ID Relay Connections 2.10 RS-232 Port Pin out of 50 pin D-Sub ConnectorGas Connections Commands via RS-232 InputGas Connections Less than 0.5 PPM Placing the System in Operation Operation EquipmentSeries Operation Preliminary Power-Off Check List Activating the Support GasesOperation Series 1 Air Flame IgnitionCarrier Gas Span GasAnalyzer Operation Sample PumpVerification of the Flame Guard Circuit Ignition and/or Flame Guard Circuit FailureSeries Operation Style Conventions Default ParametersEnter Navigation and Data EntryMenu Structure EscapeMain Menus Span System Self-Diagnostic Test ALT-SPANModel Screen Alarms Function AL-1 Defeated AL-1 High AL-1 NON-FAILSAFE AL-1 NON-LATCHING Operation Series Range Function Analog Output AdjustmentSetting up an AUTO-CAL LinearizationChanging Stream Autocal Password Group Setup Password ProtectionTiming Entering a Password Enter NEW Password Screen Logging Out Repeat Password Entry ScreenStandby Series Operation Operation Series Teledyne Analytical Instruments Series Maintenance Maintenance & TroubleshootingMaintenance Series Measuring Circuit Electrical ChecksAnode Voltage Check Electronic Stability Printed Circuit Board ReplacementCollector Cable Temperature Control Electronic CheckIgnition and/or Flame Guard Circuit Checks Sampling System Printed Circuit Board Descriptions Flame Guard and Anode Power Supply PCBProportional Temperature Controller PCB Electrometer-Amplifier PCB Maintenance Series Specifications and Initial Settings AppendixSeries Appendix Recommended Spare Parts List Appendix SeriesAnalytical Instruments PC Board Assemblies Drawing ListAppendix Series Teledyne Analytical Instruments Appendix B B1 Addendum and Testing Results