Teledyne 4060 manual Flame Ignition, 1 Air, Carrier Gas, Span Gas, Fuel

Page 43

Series 4060

Operation

 

 

 

4.3.1Air

1.Set the air source regulator to 40 psig.

2.Adjust the analyzer air regulator until the air pressure gauge reads the recommended air pressure of 7.0 psig.

After the air is flowing through the sensor and warm-up time has been completed, activate the following gases:

4.3.2 Carrier Gas

Set the carrier gas source regulator to 80 psig and adjust the analyzer sample regulator until the sample pressure gauge reads the recommended sample pressure of 7.0 psig.

4.3.3Span Gas

1.Feed span gas to the analyzer (see Section 4.6.5). Gas switching can also be handled through the autocal valves (if the option is added), which can also be manually activated as described in Section 4.6.5.

2.Observe that the analyzer sample flow meter reads from 0.3 to 1.0 SCFH.

4.3.4Fuel

1.Open the main valve on the fuel source and set the fuel pressure regulator to 40 psig.

2.Adjust the fuel regulator until its pressure gauge reads the recommended pressure of 4.0 psig.

Note: Adjust fuel settings only when the red LED (flame failure light) is off.

4.4 Flame Ignition

Observe that after warm up count down timer reaches zero (timer to preheat the sensor), the amber heater lamp is blinking (indicating that the temperature controller is maintaining the temperature setpoint) and the red Flame Out lamp is on. See Figure 1-1.

The Model 4060 will automatically attempt a flame ignition sequence following the warm up period which has been preset at the

Teledyne Analytical Instruments

43

Image 43
Contents Series Teledyne Analytical Instruments SeriesTeledyne Analytical Instruments Iii Safety MessagesSeries Combustible GAS Usage Additional Safety InformationSeries Teledyne Analytical Instruments Vii Procedure for Removal of Internal Inaccessible Shock HazardsViii Table of Contents Operation Maintenance & Troubleshooting Appendix B AppendixTeledyne Analytical Instruments Xiii List of FiguresList of Tables Introduction Main Features of the AnalyzerSeries Introduction Analyzer Description Principle of OperationIntroduction Series Model 4060 Front Panel Interface Applications Series Operational Theory Operational TheoryIntroduction Modes of OperationOperational Theory Series Analyzer SubsystemsSample System Gas Flow Control System Internal Temperature ControllersFlame Ionization Detection Cell Fuel and Blanket Air SystemsTypical Piping Diagram for the Model Detection Cell Flame Ionization Cell Electrometer-AmplifierFlame Guard Circuit Anode Power SupplyFlame Ignition Circuit Mounting the Analyzer InstallationSeries Installation Unpacking the AnalyzerElectronic Connections Installation SeriesElectrical Power Connections User ConnectionsModel 4060 Rear Panel with Optional Gas Manifold Equipment Interface Connector Pin Arrangement Pin Function Threshold Alarm System Alarm Remote Calibration Connections Range ID Relay Connections 2.10 RS-232 Port Pin out of 50 pin D-Sub ConnectorGas Connections Commands via RS-232 InputGas Connections Less than 0.5 PPM Placing the System in Operation Equipment OperationSeries Operation Activating the Support Gases Preliminary Power-Off Check ListOperation Series Span Gas Flame Ignition1 Air Carrier GasIgnition and/or Flame Guard Circuit Failure Sample PumpAnalyzer Operation Verification of the Flame Guard CircuitSeries Operation Style Conventions Default ParametersEnter Navigation and Data EntryMenu Structure EscapeMain Menus Span ALT-SPAN System Self-Diagnostic TestModel Screen Alarms Function AL-1 Defeated AL-1 High AL-1 NON-FAILSAFE AL-1 NON-LATCHING Operation Series Range Function Analog Output AdjustmentLinearization Setting up an AUTO-CALChanging Stream Autocal Password Password Protection Group SetupTiming Entering a Password Enter NEW Password Screen Logging Out Repeat Password Entry ScreenStandby Series Operation Operation Series Teledyne Analytical Instruments Series Maintenance Maintenance & TroubleshootingMeasuring Circuit Electrical Checks Maintenance SeriesAnode Voltage Check Electronic Stability Printed Circuit Board ReplacementCollector Cable Temperature Control Electronic CheckIgnition and/or Flame Guard Circuit Checks Sampling System Printed Circuit Board Descriptions Flame Guard and Anode Power Supply PCBProportional Temperature Controller PCB Electrometer-Amplifier PCB Maintenance Series Appendix Specifications and Initial SettingsSeries Appendix Appendix Series Recommended Spare Parts ListAnalytical Instruments PC Board Assemblies Drawing ListAppendix Series Teledyne Analytical Instruments Appendix B B1 Addendum and Testing Results