Directed Electronics Ready Remote manual Step

Page 17

➜

step 1

Ground Wire

The BLACK (H1/5) wire on the main 8-pin harness is ground. First strip back a ¾-inch section of the insulation off the BLACK wire and crimp a ring terminal (not provided) to that wire. Locate a clean, paint-free metal surface in the drivers kick panel. Using a self-tapping screw, drill the screw with the ring terminal to the metal area. Once screwed down, pull on the wire to ensure a good connection.

note: More problems are attributed to poor ground con- nections than any other cause. Take extra care to ensure the ground is a clean metal-to-metal contact and secure.

SELF-TAPPING

BOLT OR SCREW

GROUND

WIRE

	NOTE: REMOVE ANY PAINT	RING
DIA-591	BELOW RING CONNECTOR	TERMINAL

© 2 0 0 6 D i r e c t e d E l e c t r o n i c s

13

Image 17

Contents 24923 Page Limited lifetime consumer warranty 0 6 D i r e c t e d E l e c t r o n i c s Table of contents 0 6 D i r e c t e d E l e c t r o n i c s Installation tools What is includedImportant information System maintenanceFcc/id notice 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Main harness H1, 8-pin connector Relay heavy gauge wires Secondary harness H2, 7-pin connectorUsing LED test probe Installation RED Ignition Control Step Constant Power and Ignition wires Control Module 0 6 D i r e c t e d E l e c t r o n i c s Accessory and Starter wires +12 VDC Constant Fused 20A 0 6 D i r e c t e d E l e c t r o n i c s Safety Shutdown Wires 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Parking light flash 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Door Locks 0 6 D i r e c t e d E l e c t r o n i c s At the door lock switch Directly to the lock motors Type B negative-triggered, relay-driven system Testing reversing polarity systems 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Type D adding one or more after-market actuators Type E electrically-activated vacuum Type F one-wire system cut to lock, ground to unlock Type G positive + multiplex Power wire, or the + terminal of the battery 0 6 D i r e c t e d E l e c t r o n i c s Engine monitoring voltage-default setting-optional Identify the suspect wire according to the web information Factory Alarm Arm or Disarm 0 6 D i r e c t e d E l e c t r o n i c s Immobilizer Bypass Modules Learning the remote 0 6 D i r e c t e d E l e c t r o n i c s Testing the system Remote functions Standard configurationPress the button to unlock the vehicle Control module programming Uncut FAD Cut RAP Cancellation 0 6 D i r e c t e d E l e c t r o n i c s Using your system 0 6 D i r e c t e d E l e c t r o n i c s Locking with remote When you are ready to drive the vehicle Timer mode Pit stop mode Code hopping re-synchronize Trunk/auxiliaryTroubleshooting 0 6 D i r e c t e d E l e c t r o n i c s Glossary of terms 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Quick Reference Guide Company behind this system is Directed Electronics