Directed Electronics Ready Remote manual Using LED test probe

Page 14

using LED test probe

note: Do not use this test probe on computerized equip- ment or on the tachometer wiring as damage can result.

To use the LED test probe:

1.Remove the protective cover off the probe tip. Save the protective cover for reinstallation on the probe tip when the LED tester is not being used.

2.Connect the Black clip to a good chassis ground.

3.Connect the Red clip to a good +12V source. Both the Red and Green LEDs should be illuminated dimly.

4.If a positive voltage source is probed, the Red LED will illuminate brightly, and the Green LED will extinguish.

5.If a negative source is probed the Green LED will illu- minate brightly and the Red LED will extinguish.

Alternate procedure to use the LED test probe (only for use on probing positive voltage wires):

1.Remove the protective cover off the probe tip. Save the protective cover for reinstallation on the probe tip when the LED tester is not being used.

2.Connect the Black clip to a good chassis ground.

3.If a positive voltage source is probed, the Red LED will illuminate brightly.

10	© 2 0 0 6 D i r e c t e d E l e c t r o n i c s

Image 14

Contents 24923 Page Limited lifetime consumer warranty 0 6 D i r e c t e d E l e c t r o n i c s Table of contents 0 6 D i r e c t e d E l e c t r o n i c s What is included Installation toolsSystem maintenance Important informationFcc/id notice 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Main harness H1, 8-pin connector Secondary harness H2, 7-pin connector Relay heavy gauge wiresUsing LED test probe Installation RED Ignition Control Step Constant Power and Ignition wires Control Module 0 6 D i r e c t e d E l e c t r o n i c s Accessory and Starter wires +12 VDC Constant Fused 20A 0 6 D i r e c t e d E l e c t r o n i c s Safety Shutdown Wires 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Parking light flash 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Door Locks 0 6 D i r e c t e d E l e c t r o n i c s At the door lock switch Directly to the lock motors Type B negative-triggered, relay-driven system Testing reversing polarity systems 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Type D adding one or more after-market actuators Type E electrically-activated vacuum Type F one-wire system cut to lock, ground to unlock Type G positive + multiplex Power wire, or the + terminal of the battery 0 6 D i r e c t e d E l e c t r o n i c s Engine monitoring voltage-default setting-optional Identify the suspect wire according to the web information Factory Alarm Arm or Disarm 0 6 D i r e c t e d E l e c t r o n i c s Immobilizer Bypass Modules Learning the remote 0 6 D i r e c t e d E l e c t r o n i c s Testing the system Standard configuration Remote functionsPress the button to unlock the vehicle Control module programming Uncut FAD Cut RAP Cancellation 0 6 D i r e c t e d E l e c t r o n i c s Using your system 0 6 D i r e c t e d E l e c t r o n i c s Locking with remote When you are ready to drive the vehicle Timer mode Pit stop mode Trunk/auxiliary Code hopping re-synchronizeTroubleshooting 0 6 D i r e c t e d E l e c t r o n i c s Glossary of terms 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Quick Reference Guide Company behind this system is Directed Electronics