Directed Electronics Ready Remote manual Control Module

Page 19

the kick panel area and secure it. Probe one of the thicker gauge wires. The color and identity of your specific vehicle wiring can be obtained at www.designtech-intl.com. With the key in the off position, test the suspect wire. The constant power wire will illu- minate the Red LED on the test probe.

warning! Before making any connection to constant battery power make sure that the two green 30 amp fuses are removed from the fuse holders on the two thick red wires (heavy gauge wires). Failure to do so may cause fire or shorting of sensitive elec- trical components.

30 A

fuses

Control Module

RED heavy gauge wires

Once the constant power wire has been identified, solder the two heavy gauge RED wires from the control module (relay heavy gauge) to it and wrap the connection with electrical tape.

note: If the vehicle has two constant power wires, utilize both constant power wires. Connect one of the heavy gauge RED wires to one of the constant power wires and the other heavy gauge RED wire to the other constant power wire.

With the test probe black lead still in the kick panel, locate the ignition wire in the same location. It will test differently than

© 2 0 0 6 D i r e c t e d E l e c t r o n i c s

15

Image 19

Contents 24923 Page Limited lifetime consumer warranty 0 6 D i r e c t e d E l e c t r o n i c s Table of contents 0 6 D i r e c t e d E l e c t r o n i c s Installation tools What is includedImportant information System maintenanceFcc/id notice 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Main harness H1, 8-pin connector Relay heavy gauge wires Secondary harness H2, 7-pin connectorUsing LED test probe Installation RED Ignition Control Step Constant Power and Ignition wires Control Module 0 6 D i r e c t e d E l e c t r o n i c s Accessory and Starter wires +12 VDC Constant Fused 20A 0 6 D i r e c t e d E l e c t r o n i c s Safety Shutdown Wires 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Parking light flash 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Door Locks 0 6 D i r e c t e d E l e c t r o n i c s At the door lock switch Directly to the lock motors Type B negative-triggered, relay-driven system Testing reversing polarity systems 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Type D adding one or more after-market actuators Type E electrically-activated vacuum Type F one-wire system cut to lock, ground to unlock Type G positive + multiplex Power wire, or the + terminal of the battery 0 6 D i r e c t e d E l e c t r o n i c s Engine monitoring voltage-default setting-optional Identify the suspect wire according to the web information Factory Alarm Arm or Disarm 0 6 D i r e c t e d E l e c t r o n i c s Immobilizer Bypass Modules Learning the remote 0 6 D i r e c t e d E l e c t r o n i c s Testing the system Remote functions Standard configurationPress the button to unlock the vehicle Control module programming Uncut FAD Cut RAP Cancellation 0 6 D i r e c t e d E l e c t r o n i c s Using your system 0 6 D i r e c t e d E l e c t r o n i c s Locking with remote When you are ready to drive the vehicle Timer mode Pit stop mode Code hopping re-synchronize Trunk/auxiliaryTroubleshooting 0 6 D i r e c t e d E l e c t r o n i c s Glossary of terms 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Quick Reference Guide Company behind this system is Directed Electronics