Directed Electronics Ready Remote manual Using your system

Page 57

using your system

warning! safety first

The following safety warnings must be observed at all times:

When properly installed, this system can start the vehicle via a command signal from the remote. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user's sole responsibility to properly handle and keep out of reach from children all remotes to assure that the system does not unintentionally remote start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJA- CENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED. These precau- tions are the sole responsibility of the user.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user must also have the neutral safety feature of the vehicle periodically checked, wherein the vehicle

© 2 0 0 6 D i r e c t e d E l e c t r o n i c s

53

Image 57
Contents 24923 Page Limited lifetime consumer warranty 0 6 D i r e c t e d E l e c t r o n i c s Table of contents 0 6 D i r e c t e d E l e c t r o n i c s Installation tools What is includedImportant information System maintenanceFcc/id notice 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Main harness H1, 8-pin connector Relay heavy gauge wires Secondary harness H2, 7-pin connectorUsing LED test probe Installation RED Ignition Control Step Constant Power and Ignition wires Control Module 0 6 D i r e c t e d E l e c t r o n i c s Accessory and Starter wires +12 VDC Constant Fused 20A 0 6 D i r e c t e d E l e c t r o n i c s Safety Shutdown Wires 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Parking light flash 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Door Locks 0 6 D i r e c t e d E l e c t r o n i c s At the door lock switch Directly to the lock motors Type B negative-triggered, relay-driven system Testing reversing polarity systems 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Type D adding one or more after-market actuators Type E electrically-activated vacuum Type F one-wire system cut to lock, ground to unlock Type G positive + multiplex Power wire, or the + terminal of the battery 0 6 D i r e c t e d E l e c t r o n i c s Engine monitoring voltage-default setting-optional Identify the suspect wire according to the web information Factory Alarm Arm or Disarm 0 6 D i r e c t e d E l e c t r o n i c s Immobilizer Bypass Modules Learning the remote 0 6 D i r e c t e d E l e c t r o n i c s Testing the system Remote functions Standard configurationPress the button to unlock the vehicle Control module programming Uncut FAD Cut RAP Cancellation 0 6 D i r e c t e d E l e c t r o n i c s Using your system 0 6 D i r e c t e d E l e c t r o n i c s Locking with remote When you are ready to drive the vehicle Timer mode Pit stop mode Code hopping re-synchronize Trunk/auxiliaryTroubleshooting 0 6 D i r e c t e d E l e c t r o n i c s Glossary of terms 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Quick Reference Guide Company behind this system is Directed Electronics