Directed Electronics Ready Remote manual Troubleshooting

Page 64

troubleshooting

➤The ignition comes on, but the starter will not crank. Does it start with the key in the ignition? If so, does the vehicle have an engine immobilizer?

Will it start with the brake pedal depressed? (Make sure to disconnect the brake shutdown when performing this test.) If so, it may have a brake/starter interlock.

Is the correct starter wire being energized? Check by ener- gizing it yourself with a fused test lead.

➤The starter cranks for 1 or 2-seconds but does not start. Either the wrong ignition wire is being energized, the system’s ignition and accessory wires have been connected backwards, or the vehicle has two ignition circuits. Try activating the unit with the ignition key in the “run” position. If the vehicle then runs normally, retest your ignition system.

➤The starter continues to crank even though the engine has started.

Has the tach wire been learned? See the Tach Learning section of this guide.

Is the tach wire receiving the correct information? Either the wrong tach wire has been used, or a bad connection exists.

Verify that all of the heavy gauge wires are plugged into the correct tabs on the control unit. If they are incorrectly connected, the starter could stay engaged.

60	© 2 0 0 6 D i r e c t e d E l e c t r o n i c s

Image 64

Contents 24923 Page Limited lifetime consumer warranty 0 6 D i r e c t e d E l e c t r o n i c s Table of contents 0 6 D i r e c t e d E l e c t r o n i c s What is included Installation toolsSystem maintenance Important informationFcc/id notice 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Main harness H1, 8-pin connector Secondary harness H2, 7-pin connector Relay heavy gauge wiresUsing LED test probe Installation RED Ignition Control Step Constant Power and Ignition wires Control Module 0 6 D i r e c t e d E l e c t r o n i c s Accessory and Starter wires +12 VDC Constant Fused 20A 0 6 D i r e c t e d E l e c t r o n i c s Safety Shutdown Wires 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Parking light flash 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Door Locks 0 6 D i r e c t e d E l e c t r o n i c s At the door lock switch Directly to the lock motors Type B negative-triggered, relay-driven system Testing reversing polarity systems 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Type D adding one or more after-market actuators Type E electrically-activated vacuum Type F one-wire system cut to lock, ground to unlock Type G positive + multiplex Power wire, or the + terminal of the battery 0 6 D i r e c t e d E l e c t r o n i c s Engine monitoring voltage-default setting-optional Identify the suspect wire according to the web information Factory Alarm Arm or Disarm 0 6 D i r e c t e d E l e c t r o n i c s Immobilizer Bypass Modules Learning the remote 0 6 D i r e c t e d E l e c t r o n i c s Testing the system Standard configuration Remote functionsPress the button to unlock the vehicle Control module programming Uncut FAD Cut RAP Cancellation 0 6 D i r e c t e d E l e c t r o n i c s Using your system 0 6 D i r e c t e d E l e c t r o n i c s Locking with remote When you are ready to drive the vehicle Timer mode Pit stop mode Trunk/auxiliary Code hopping re-synchronizeTroubleshooting 0 6 D i r e c t e d E l e c t r o n i c s Glossary of terms 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Quick Reference Guide Company behind this system is Directed Electronics