Directed Electronics Ready Remote manual +12 VDC Constant Fused 20A

Page 22

insulation off a small portion and solder the thick ORANGE (3) wire of the heavy gauge wire and wrap it with electrical tape.

If your vehicle requires more than one accessory, an additional relay (not provided) is required. Refer to the diagram below.

+12 VDC CONSTANT (FUSED 20A)

			ACCESSORY RELAY
			(NOT PROVIDED)
	TO ACCESSORY	87	GROUND
	TO ACCESSORY		GROUND
	86	87A	85
		30
			TO ACCESSORY
	+12 VDC CONSTANT (FUSED 20A)
			2nd ACCESSORY RELAY
			(NOT PROVIDED)
	ORANGE (+) 30A OUTPUT TO	87
	ACCESSORY CIRCUIT	87	GROUND
	ACCESSORY CIRCUIT		GROUND
	86	87A	85
		30
		TO 2nd ACCESSORY

Now that the accessories have been located, find the wire suspected to be the starter wire according to the web information on your vehicle. Place the red lead of your LED tester on the

18	© 2 0 0 6 D i r e c t e d E l e c t r o n i c s

Image 22

Contents 24923 Page Limited lifetime consumer warranty 0 6 D i r e c t e d E l e c t r o n i c s Table of contents 0 6 D i r e c t e d E l e c t r o n i c s What is included Installation toolsSystem maintenance Important informationFcc/id notice 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Main harness H1, 8-pin connector Secondary harness H2, 7-pin connector Relay heavy gauge wiresUsing LED test probe Installation RED Ignition Control Step Constant Power and Ignition wires Control Module 0 6 D i r e c t e d E l e c t r o n i c s Accessory and Starter wires +12 VDC Constant Fused 20A 0 6 D i r e c t e d E l e c t r o n i c s Safety Shutdown Wires 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Parking light flash 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Door Locks 0 6 D i r e c t e d E l e c t r o n i c s At the door lock switch Directly to the lock motors Type B negative-triggered, relay-driven system Testing reversing polarity systems 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Type D adding one or more after-market actuators Type E electrically-activated vacuum Type F one-wire system cut to lock, ground to unlock Type G positive + multiplex Power wire, or the + terminal of the battery 0 6 D i r e c t e d E l e c t r o n i c s Engine monitoring voltage-default setting-optional Identify the suspect wire according to the web information Factory Alarm Arm or Disarm 0 6 D i r e c t e d E l e c t r o n i c s Immobilizer Bypass Modules Learning the remote 0 6 D i r e c t e d E l e c t r o n i c s Testing the system Standard configuration Remote functionsPress the button to unlock the vehicle Control module programming Uncut FAD Cut RAP Cancellation 0 6 D i r e c t e d E l e c t r o n i c s Using your system 0 6 D i r e c t e d E l e c t r o n i c s Locking with remote When you are ready to drive the vehicle Timer mode Pit stop mode Trunk/auxiliary Code hopping re-synchronizeTroubleshooting 0 6 D i r e c t e d E l e c t r o n i c s Glossary of terms 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Quick Reference Guide Company behind this system is Directed Electronics