Directed Electronics Ready Remote manual Pit stop mode

Page 62

■The shutdown toggle switch is put into the ON position.

■Note: The button on the remote can be pressed twice at any time to stop the engine during the 12-minute timer

engine run interval. The button does not affect the 3-hour time interval between engine starts. If the engine fails to start on

3 attempts it is counted as one start in timer mode. The system will attempt to start again 3-hours later (if this wasn’t its 6th

start attempt).

pit stop mode

This feature allows you to exit the car and leave the engine running. Use the following procedure to enter Pit Stop Mode:

1.Place the transmission in park and put the parking brake on.

2.Leave the ignition on.

3.Do not step on the brake.

4.Press the button twice. The parking lights will flash once to confirm pit stop mode.

5.Turn the key off and remove the key.

6.Exit and lock the vehicle.

58	© 2 0 0 6 D i r e c t e d E l e c t r o n i c s

Image 62

Contents 24923 Page Limited lifetime consumer warranty 0 6 D i r e c t e d E l e c t r o n i c s Table of contents 0 6 D i r e c t e d E l e c t r o n i c s What is included Installation toolsSystem maintenance Important informationFcc/id notice 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Main harness H1, 8-pin connector Secondary harness H2, 7-pin connector Relay heavy gauge wiresUsing LED test probe Installation RED Ignition Control Step Constant Power and Ignition wires Control Module 0 6 D i r e c t e d E l e c t r o n i c s Accessory and Starter wires +12 VDC Constant Fused 20A 0 6 D i r e c t e d E l e c t r o n i c s Safety Shutdown Wires 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Parking light flash 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Door Locks 0 6 D i r e c t e d E l e c t r o n i c s At the door lock switch Directly to the lock motors Type B negative-triggered, relay-driven system Testing reversing polarity systems 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Type D adding one or more after-market actuators Type E electrically-activated vacuum Type F one-wire system cut to lock, ground to unlock Type G positive + multiplex Power wire, or the + terminal of the battery 0 6 D i r e c t e d E l e c t r o n i c s Engine monitoring voltage-default setting-optional Identify the suspect wire according to the web information Factory Alarm Arm or Disarm 0 6 D i r e c t e d E l e c t r o n i c s Immobilizer Bypass Modules Learning the remote 0 6 D i r e c t e d E l e c t r o n i c s Testing the system Standard configuration Remote functionsPress the button to unlock the vehicle Control module programming Uncut FAD Cut RAP Cancellation 0 6 D i r e c t e d E l e c t r o n i c s Using your system 0 6 D i r e c t e d E l e c t r o n i c s Locking with remote When you are ready to drive the vehicle Timer mode Pit stop mode Trunk/auxiliary Code hopping re-synchronizeTroubleshooting 0 6 D i r e c t e d E l e c t r o n i c s Glossary of terms 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Quick Reference Guide Company behind this system is Directed Electronics