Directed Electronics Ready Remote manual 0 6 D i r e c t e d E l e c t r o n i c s

Page 50

note: The system can only learn, after being connected and with the FIRST IGNITION ON. If not learned with the first ignition on the main power fuses will have to be dis- connected from the READY REMOTE unit and then reconnected and the procedure repeated.

3.Program. Within 10-seconds, press and hold the PROG

button on the transmitter, until the parking lights turn off and then back on. Now release the PROG button. Repeat

this step within 10-seconds of programming a transmitter to program additional transmitters to your system.

note: A second remote can only be added to the system immediately after programming the first remote.

important: When programming a remote ensure to hold the remote about 4-feet away from the Directed unit. If the remote is too close to the unit, the remote may not program.

4.Exit Learn Mode. After programming the transmitter, wait 10-seconds, the parking lights will turn off. Programming transmitter(s) is now complete.

46	© 2 0 0 6 D i r e c t e d E l e c t r o n i c s

Image 50

Contents 24923 Page Limited lifetime consumer warranty 0 6 D i r e c t e d E l e c t r o n i c s Table of contents 0 6 D i r e c t e d E l e c t r o n i c s What is included Installation toolsSystem maintenance Important informationFcc/id notice 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Main harness H1, 8-pin connector Secondary harness H2, 7-pin connector Relay heavy gauge wiresUsing LED test probe Installation RED Ignition Control Step Constant Power and Ignition wires Control Module 0 6 D i r e c t e d E l e c t r o n i c s Accessory and Starter wires +12 VDC Constant Fused 20A 0 6 D i r e c t e d E l e c t r o n i c s Safety Shutdown Wires 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Parking light flash 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Door Locks 0 6 D i r e c t e d E l e c t r o n i c s At the door lock switch Directly to the lock motors Type B negative-triggered, relay-driven system Testing reversing polarity systems 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Type D adding one or more after-market actuators Type E electrically-activated vacuum Type F one-wire system cut to lock, ground to unlock Type G positive + multiplex Power wire, or the + terminal of the battery 0 6 D i r e c t e d E l e c t r o n i c s Engine monitoring voltage-default setting-optional Identify the suspect wire according to the web information Factory Alarm Arm or Disarm 0 6 D i r e c t e d E l e c t r o n i c s Immobilizer Bypass Modules Learning the remote 0 6 D i r e c t e d E l e c t r o n i c s Testing the system Standard configuration Remote functionsPress the button to unlock the vehicle Control module programming Uncut FAD Cut RAP Cancellation 0 6 D i r e c t e d E l e c t r o n i c s Using your system 0 6 D i r e c t e d E l e c t r o n i c s Locking with remote When you are ready to drive the vehicle Timer mode Pit stop mode Trunk/auxiliary Code hopping re-synchronizeTroubleshooting 0 6 D i r e c t e d E l e c t r o n i c s Glossary of terms 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Quick Reference Guide Company behind this system is Directed Electronics