Directed Electronics Ready Remote manual Parking light flash

Page 27

HOOD PIN SWITCH -

OPEN WHEN HOOD IS CLOSED

HOOD PIN SWITCH -

CONNECTOR

GRAY WIRE

TO GRAY (H1/5) WIRE

ON

CONTROL MODULE

BYPASS

TOGGLE

SWITCH

BLACK WIRE	BYPASSED WHEN CLOSED

➜

step 5

Parking light flash

There are several different types of parking light circuits. The following description is for a standard positive-triggered parking light circuit, only. If the web vehicle information suggests a (-) parking light circuit, the fusible jumper (under the sliding door on the control module) must be moved to the opposite position. The default position for this jumper is for a positive parking light. Refer to the LED test probe procedures if you have a negative parking light circuit.

note: When parking lights are connected, they will flash for the whole time that remote start is active.

© 2 0 0 6 D i r e c t e d E l e c t r o n i c s

23

Image 27

Contents 24923 Page Limited lifetime consumer warranty 0 6 D i r e c t e d E l e c t r o n i c s Table of contents 0 6 D i r e c t e d E l e c t r o n i c s Installation tools What is includedImportant information System maintenanceFcc/id notice 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Main harness H1, 8-pin connector Relay heavy gauge wires Secondary harness H2, 7-pin connectorUsing LED test probe Installation RED Ignition Control Step Constant Power and Ignition wires Control Module 0 6 D i r e c t e d E l e c t r o n i c s Accessory and Starter wires +12 VDC Constant Fused 20A 0 6 D i r e c t e d E l e c t r o n i c s Safety Shutdown Wires 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Parking light flash 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Door Locks 0 6 D i r e c t e d E l e c t r o n i c s At the door lock switch Directly to the lock motors Type B negative-triggered, relay-driven system Testing reversing polarity systems 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Type D adding one or more after-market actuators Type E electrically-activated vacuum Type F one-wire system cut to lock, ground to unlock Type G positive + multiplex Power wire, or the + terminal of the battery 0 6 D i r e c t e d E l e c t r o n i c s Engine monitoring voltage-default setting-optional Identify the suspect wire according to the web information Factory Alarm Arm or Disarm 0 6 D i r e c t e d E l e c t r o n i c s Immobilizer Bypass Modules Learning the remote 0 6 D i r e c t e d E l e c t r o n i c s Testing the system Remote functions Standard configurationPress the button to unlock the vehicle Control module programming Uncut FAD Cut RAP Cancellation 0 6 D i r e c t e d E l e c t r o n i c s Using your system 0 6 D i r e c t e d E l e c t r o n i c s Locking with remote When you are ready to drive the vehicle Timer mode Pit stop mode Code hopping re-synchronize Trunk/auxiliaryTroubleshooting 0 6 D i r e c t e d E l e c t r o n i c s Glossary of terms 0 6 D i r e c t e d E l e c t r o n i c s 0 6 D i r e c t e d E l e c t r o n i c s Quick Reference Guide Company behind this system is Directed Electronics