GTO RB923 rev installation manual Parts, Hardware not to scale

Page 12

Single Gate Operator Parts List

8" Nylon Cable Tie (14)

Parts
	Gate Operator with 6 ft. Power Cable
	Post Pivot Brackets (2)
Gate Bracket	Post Bracket	Rear Mount
Closed Position Stop Plate

Hardware (not to scale)

1/2" x 10" Carriage Bolt (2)

1	/2" x 3	3	/4" Bolt (2)	11/4"dia x 1/2" Nylon Spacer (2)
	/2" x 3		/4" Bolt (2)

1/2" x 23/4" Bolt (3)		1/2"dia x 17/16" Metal Spacer (1)
	(4)	1/2"dia x 17/16" Metal Spacer (1)
	(4)
3/8" x 11/2" Bolt (1)	Screw	1/2" Washer (6)
3/8" x 11/2" Bolt (1)
	Mounting
1/2" x 11/4" Clevis Pin (1)	Mounting	1/2" Lock Nut (7)
1/2" x 11/4" Clevis Pin (1)
Hairpin Clip (1)	Receiver	3/8" Lock Nut (1)
Hairpin Clip (1)
	2"

9

Image 12

Contents Series Converting Temperature Table of Contents Important Safety Instructions Disconnecting the OperatorBefore Installation II. During InstallationIII. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentConsumer/End User No ONE should Cross the Path of the Moving GateRequired Safety Precautions for Swing Gates Install Warning SignsEntrapment Protection Moving Gate Can Cause Injury Or Death Technical Specifications GTO/PRO 2000 Series Swing Gate OperatorsParts Hardware not to scaleSingle Gate Operator Parts List Control Box and Electrical ComponentsPreparing the Gate Pull-to-Open Single Gate gate opens into the propertyStep Installing The Post Bracket Assembly Step Connecting Operator to Post Bracket Assembly 1/ nut. Note when tighteningRear mount bolt, leave it loose Enough for the operator to pivotInstalling the Gate Bracket Installing the Open and Closed Position Stops Mounting the Control Box Never insert the battery with the terminals to the right BatteryPowering the System Gate LengthSplice wires together Solar Zones and Gate ActivityEstimated Maximum Number of Cycles Per Day Make sure the exposed wires do not touch each other Not touch each otherControl Board Settings DIP SwitchesPotentiometers Setting the Personal Transmitter Code Set the transmitter DIP SwitchesRemove the Transmitter Cover Mounting the Receiver MemoryRun the cable through PVC conduit to protect it from damage Setting the Closed Position Limit Switch Step For Pull-to-Open InstallationsFor Push-to-Open Installations Step Connecting Additional Safety Devices Compatible Safety Devices Safety EdgesPhotoelectric Beams Connecting Accessories WHT white used with GRN greenBLU blue used with GRN green ORG orange used with GRN greenPush-to-Open Installation Step PTO-1Step PTO-2 Step PTO-3 Step PTO-4Step PTO-5 Step PTO-6Maintenance and Troubleshooting Guide MaintenancePage Warranty and Repair Service Limited Two Year WarrantyGTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USA Column Installation Information Second Unit Parts List GTO/PRO 2200 Dual Gate SystemInstalling The Second Unit GTO Automatic Gate Lock see Accessory CatalogStep D1 StepD2Connecting the Second Operator to the Control Board StepD3Step D-4 Step D-5Setting the Control Board for Dual Gate Installations Step D-7Step D-8 Step D-9Step D-11 Accessories Available Through Your Dealer RB101GTO Nema Box FM317 ACCESS-ories 433IHRB509 Master Pin Lock RB975Access -ories Replacement BatteriesInstallation Check list Installation of this operator conforms to Class