GTO RB923 rev installation manual Push-to-Open Installation, Step PTO-1, Step PTO-2

Page 34

Push-to-Open Installation

Determining The Mounting Position of The Post Bracket Assembly

Swinging gates shall not open into public access areas! Review IMPORTANT SAFETY INSTRUCTIONS

A "Push-to-Open" gate opens out from the property. The operator is installed on this type of gate while in the closed (not open) position. Because every gate installation varies, the push-to-open installation of the GTO/PRO 2000 and GTO/PRO 2200 will need to be customized. In most cases this only requires drilling two new holes in the post bracket.

Step PTO-1:

The operator and brackets are installed on the gate post in the same way as pull-to-open installations. The post bracket is mounted at the inside edge of the post. The post pivot brackets are attached with one bolt at the pivot point and the operator(s) is attached at the rear mount. See pages 11-14, Steps 1-9 for details.

Open Position

Step PTO-2:

Find a position for the post pivot brackets where the operator has clearance in both the open and closed positions and clamp operator into position (see examples of clearance on page 15; step 10). Mark the point on the post pivot bracket where the 1/2" holes will need to be drilled. Drill the holes then secure the post pivot bracket using the 1/2" bolt, spacer, washer and lock nut.

Clearance

Closed Position

New Hole Position

Spacer

31

Image 34

Contents Series Converting Temperature Table of Contents Important Safety Instructions Disconnecting the OperatorBefore Installation II. During InstallationIII. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentConsumer/End User No ONE should Cross the Path of the Moving GateInstall Warning Signs Required Safety Precautions for Swing GatesEntrapment Protection Moving Gate Can Cause Injury Or Death Technical Specifications GTO/PRO 2000 Series Swing Gate OperatorsParts Hardware not to scaleSingle Gate Operator Parts List Control Box and Electrical ComponentsPull-to-Open Single Gate gate opens into the property Preparing the GateStep Installing The Post Bracket Assembly Step Rear mount bolt, leave it loose Connecting Operator to Post Bracket Assembly1/ nut. Note when tightening Enough for the operator to pivotInstalling the Gate Bracket Installing the Open and Closed Position Stops Mounting the Control Box Never insert the battery with the terminals to the right BatteryPowering the System Gate LengthSolar Zones and Gate Activity Splice wires togetherEstimated Maximum Number of Cycles Per Day Make sure the exposed wires do not touch each other Not touch each otherControl Board Settings DIP SwitchesPotentiometers Set the transmitter DIP Switches Setting the Personal Transmitter CodeRemove the Transmitter Cover Memory Mounting the ReceiverRun the cable through PVC conduit to protect it from damage Step For Pull-to-Open Installations Setting the Closed Position Limit SwitchFor Push-to-Open Installations Step Connecting Additional Safety Devices Safety Edges Compatible Safety DevicesPhotoelectric Beams BLU blue used with GRN green Connecting AccessoriesWHT white used with GRN green ORG orange used with GRN greenStep PTO-1 Push-to-Open InstallationStep PTO-2 Step PTO-5 Step PTO-3Step PTO-4 Step PTO-6Maintenance and Troubleshooting Guide MaintenancePage Limited Two Year Warranty Warranty and Repair ServiceGTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USA Column Installation Information Second Unit Parts List GTO/PRO 2200 Dual Gate SystemStep D1 Installing The Second UnitGTO Automatic Gate Lock see Accessory Catalog StepD2Step D-4 Connecting the Second Operator to the Control BoardStepD3 Step D-5Step D-8 Setting the Control Board for Dual Gate InstallationsStep D-7 Step D-9Step D-11 RB101 Accessories Available Through Your DealerGTO Nema Box FM317 RB509 ACCESS-ories433IH Master Pin Lock RB975Access -ories Replacement BatteriesInstallation Check list Installation of this operator conforms to Class