GTO RB923 rev installation manual Moving Gate Can Cause Injury Or Death

Page 10

IMPORTANT SAFETY INSTRUCTIONS

Warning Signs and Labels

These warning labels should be found at the locations specified below. If any of them are missing, immediately contact GTO for replacements.

!WARNING

Moving Gate Can Cause

Injury Or Death

1.KEEP CLEAR! Gate may move at any time.

2.Do not allow children to operate gate or play in gate area.

3.This gate is for vehicles only. Pedestrians must use a separate entrance.

warning signs (2 enclosed) to be installed on each side of the gate (3–5 feet above the bottom of the gate)

!WARNING

MOVING GATE

Can Cause Injury or Death

1.KEEP CLEAR! Gate may move at any time.

2.Do not allow children to operate gate or play in gate area.

3.This gate is for vehicles only. Pedestrians must use

separate entrance.

RB979

warning labels (2) installed on each side of operator housing

¤

CUS

LI	D
	S TE

9901178

2000 Series

Conforms to UL 325 STANDARDS

Maximum Gate: 1000 lb. (453.5 kg); 20 ft. (6.1 m)

Voltage: 12 Vdc; Frequency: 0 Hz; Power: 49.7 W Class I, II and III Vehicular Swing Gate Operator. Serial Number: 2000-xxxxxxx

TO MANUALLY OPEN AND CLOSE THE GATE:

1.Turn control box power switch OFF.

2.Remove hairpin clip and clevis pin from front mount.

3.Pull front mount away from gate bracket.

Disconnect operator ONLY when the control box power switch is OFF and the gate is NOT moving.

GTO, Inc. Tallahassee, Florida USA

RB2002

product identification and manual operation label installed on control box cover

7

Image 10

Contents Series Converting Temperature Table of Contents Important Safety Instructions Disconnecting the OperatorBefore Installation II. During InstallationIII. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentConsumer/End User No ONE should Cross the Path of the Moving GateInstall Warning Signs Required Safety Precautions for Swing GatesEntrapment Protection Moving Gate Can Cause Injury Or Death Technical Specifications GTO/PRO 2000 Series Swing Gate OperatorsParts Hardware not to scaleSingle Gate Operator Parts List Control Box and Electrical ComponentsPull-to-Open Single Gate gate opens into the property Preparing the GateStep Installing The Post Bracket Assembly Step Rear mount bolt, leave it loose Connecting Operator to Post Bracket Assembly1/ nut. Note when tightening Enough for the operator to pivotInstalling the Gate Bracket Installing the Open and Closed Position Stops Mounting the Control Box Never insert the battery with the terminals to the right BatteryPowering the System Gate LengthSolar Zones and Gate Activity Splice wires togetherEstimated Maximum Number of Cycles Per Day Make sure the exposed wires do not touch each other Not touch each otherControl Board Settings DIP SwitchesPotentiometers Set the transmitter DIP Switches Setting the Personal Transmitter CodeRemove the Transmitter Cover Memory Mounting the ReceiverRun the cable through PVC conduit to protect it from damage Step For Pull-to-Open Installations Setting the Closed Position Limit SwitchFor Push-to-Open Installations Step Connecting Additional Safety Devices Safety Edges Compatible Safety DevicesPhotoelectric Beams BLU blue used with GRN green Connecting AccessoriesWHT white used with GRN green ORG orange used with GRN greenStep PTO-1 Push-to-Open InstallationStep PTO-2 Step PTO-5 Step PTO-3Step PTO-4 Step PTO-6Maintenance and Troubleshooting Guide MaintenancePage Limited Two Year Warranty Warranty and Repair ServiceGTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USA Column Installation Information Second Unit Parts List GTO/PRO 2200 Dual Gate SystemStep D1 Installing The Second UnitGTO Automatic Gate Lock see Accessory Catalog StepD2Step D-4 Connecting the Second Operator to the Control BoardStepD3 Step D-5Step D-8 Setting the Control Board for Dual Gate InstallationsStep D-7 Step D-9Step D-11 RB101 Accessories Available Through Your DealerGTO Nema Box FM317 RB509 ACCESS-ories433IH Master Pin Lock RB975Access -ories Replacement BatteriesInstallation Check list Installation of this operator conforms to Class