Bosch Appliances UPH-2D Description, Outdoor Pole Mount for UPH Series, Pole Adapter for MTC-WUPH

Page 12

12 en Installing the High Speed Pan/Tilt	High Speed Pan/Tilt System

CAUTION! Medium Risk:

Be sure to use appropriately strong and load bearing bolts and other fixing

!materials when installing any UPH mountings to any surface.

When the MTC-WUPH Wall Mount is fixed to a wall, each fixing dowel must be able to support a traction load of 300daN or more. It is necessary to use 8 mm (0.315 in.) diameter bolts with appropriate length.

3.Attach the optional wall or pole mount according to the specific mounting manual (see Table 4.1 for mounting options).

Part #	Description

MTC-PUPH	Outdoor Pole Mount for UPH Series

MTC-WUPH	Outdoor Wall Mount for UPH Series

MTC-POLE-W	Pole Adapter for MTC-WUPH

MTC-CORN-W	Corner Adapter for MTC-WUPH

Table 4.1 Mounting Options

NOTICE!

i If using a washer kit, the spray support should be installed before positioning and wiring the pan/tilt. For additional information, see Section 5 Connecting the Washer Pump (optional).

4.Remove the cable glands from the base and fit the gasket / seal ring (see Figure 4.3).

5.Insert the cables into the cable glands while holding the base approx. 20 cm from the bracket (see Figure 4.2). Note that there are three glands; one for power, one for video, and one for data / IO cables.

Fig. 4.2 Inserting the Cables through the Cable Glands

6.Securely lock the cable glands into place (gland closing torque 5 Nm); they accept cables 5-10 mm in diameter. The cable glands can be changed to accept smaller 3-7 mm in diam- eter cables, available from www.cembre.com and browse "Cable glands IP68 MAXIblock" (model number: 1910.M16 M16x1.5 ). The gland (5-10 mm or 3-7 mm) closing torque is 5 Nm; use a calibrated torque wrench to ensure closure.

7.Position the base on the optional wall or pole mount, guiding the cables so that they are positioned inside the wall or pole mount (see Figure 4.3).

F01U.073.990 Version 1.0 2007.07

Instruction Manual

Bosch Security Systems

Image 12

Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Safety Important safety instructionsSafety precautions Important notices Coax groundingCopyright TrademarksParts List 2UnpackingTools Required Small, straight-blade screwdriver 2.5 mm 0.1Safety Rules 3DescriptionInstalling the High Speed Pan/Tilt Mounting the High Speed Pan/TiltWarranties are void Description Outdoor Pole Mount for UPH SeriesOutdoor Wall Mount for UPH Series Pole Adapter for MTC-WUPHReference # Description Base Gasket Screw Ring Washer Bracket SupportWiring the Video Cable Tie Threads used to Group and Secure Signal CablesConnecting the Power Supply That the disconnecting switch is openWire Color VAC Terminal Connection Per local Installer Neutral Live/Active Green/Yellow EarthWiring Biphase RS-232 is used for firmware upgrades only see Figure5RS-232 Connecting the Washer Pump optional Washer Pipe NutNosecap CouplingCalibrating the Nozzle Reference Description AL1Connecting the Peripherals Base with 19-pin Connector for Connecting PeripheralsMetal Fixing Accessory Attaching the Top UnitSalt Bag Fixing ScrewsAligning the Tabs Configuration Window Place safety label near unit that warns of moving partsScrew Screw SealConfiguring the Device Baud Rate SwitchesRocker for DIP switch No is OFF PROGRAM. OFF For updating the firmwareProtocol Switches Setting the AddressProtocol Baud Rate Menu setup OSD Pelco D 2400 Preset Biphase Auto AUX-On BilinxAddress Combinations 4Connections RS-485 Divar Biphase RS-485 Biphase Bilinx/Video IntuikeyboardIntuikeyboard AllegiantRS485-2 EthernetEthernet VideoSwitching On and Off Configuring the DeviceTo configure the UPH, proceed as follows Using the Joystick On-screen Display OSDMoving Around the Menus Open or Iris Close button10.1 Keyboard Commands List Setup and ConfigurationPresets Auxiliary ConnectionsConfiguring the System 10.2 Changing the Settings10.3 Changing the Numeric Fields Main menu by pressing AUX on 200 Enter11.2 Display Setup Menu 11.1 Language MenuPlayed on the screen Feature Description Default Options Enables / disables the on-screen message By the device Enables the user to edit a customized, onArea Parameters Menu Depending on the horizontal position reachedSetting the Area Position Values Changing the Edit Text MenuDisplay Parameters Offset PanWiper-washer, and the alarm settings of the UPH 11.3 Motion Parameters MenuSpeed Menu Data is expressed as degrees per second PAN SpeedTilt Speed Limits Preset/Patrol/Autopan Feature DescriptionPreset Menu Special Preset Parameters Home Position Reached SpeedPatrol loading of preset positions Start PositionEND Position First Prst SpeedAutopan menu is used to indicate preset position settings AutopanMotions Recall Menu Wiper-Washer Alarms 11.4 Camera ParametersUPH-2D and UPH-3D Series DinionXF Cameras UPH-Z Series camera module Zoom Parameters MenuFocus Parameters menu is used to enable focus settings Focus Parameters MenuParameters Mode Infrared Menu Auto Exposure Parameters MenuDynamic Masking UPH-Z Series only Mask NR Mask ChangingPosition Recall Changing ColourPTZ Mode Masking 11.5 Creating a New Dynamic MaskBack Light Compen SATImage Stabilization 11.6 Load Default Configuration 11.7 Setup Info MenuLoad Default menu is used to load the default settings UPH boardsMaintenance 12.1 Cleaning12.2 Replacing the Fuses Voltage Fuse F1 Fuse F2Troubleshooting Problem Possible Cause SolutionTroubleshooting Error 13.1 Dimensions and Range of Movement 514 584R385 Technical Specifications Bosch Security Systems