Bosch Appliances UPH-3D, UPH-2D, UPH-Z instruction manual Copyright, Trademarks

Page 8

8	en Safety	High Speed Pan/Tilt System

redundant recording systems, and a procedure to back up all analog and digital information.

Copyright

This user guide is the intellectual property of Bosch Security Systems and is protected by copyright.

Trademarks

All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

NOTICE!

This user guide has been compiled with great care and the information it contains has been thoroughly verified. The text

i was complete and correct at the time of printing. The ongoing development of the products may mean that the content of the user guide can change without notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness or discrepancies between the user guide and the product described.

F01U.073.990 Version 1.0 2007.07

Instruction Manual

Bosch Security Systems

Image 8

Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Safety Important safety instructionsSafety precautions Important notices Coax groundingCopyright TrademarksParts List 2UnpackingTools Required Small, straight-blade screwdriver 2.5 mm 0.1Safety Rules 3DescriptionWarranties are void Installing the High Speed Pan/TiltMounting the High Speed Pan/Tilt Description Outdoor Pole Mount for UPH SeriesOutdoor Wall Mount for UPH Series Pole Adapter for MTC-WUPHReference # Description Base Gasket Screw Ring Washer Bracket SupportWiring the Video Cable Tie Threads used to Group and Secure Signal CablesConnecting the Power Supply That the disconnecting switch is openWire Color VAC Terminal Connection Per local Installer Neutral Live/Active Green/Yellow Earth5RS-232 Wiring BiphaseRS-232 is used for firmware upgrades only see Figure Connecting the Washer Pump optional Washer Pipe NutNosecap CouplingCalibrating the Nozzle Reference Description AL1Connecting the Peripherals Base with 19-pin Connector for Connecting PeripheralsMetal Fixing Accessory Attaching the Top UnitSalt Bag Fixing ScrewsAligning the Tabs Configuration Window Place safety label near unit that warns of moving partsScrew Screw SealConfiguring the Device Baud Rate SwitchesRocker for DIP switch No is OFF PROGRAM. OFF For updating the firmwareProtocol Switches Setting the AddressProtocol Baud Rate Menu setup OSD Pelco D 2400 Preset Biphase Auto AUX-On BilinxAddress Combinations 4Connections RS-485 Divar Biphase RS-485 Biphase Bilinx/Video IntuikeyboardIntuikeyboard AllegiantRS485-2 EthernetEthernet VideoTo configure the UPH, proceed as follows Switching On and OffConfiguring the Device Using the Joystick On-screen Display OSDMoving Around the Menus Open or Iris Close button10.1 Keyboard Commands List Setup and ConfigurationPresets Auxiliary ConnectionsConfiguring the System 10.2 Changing the Settings10.3 Changing the Numeric Fields Main menu by pressing AUX on 200 EnterPlayed on the screen 11.2 Display Setup Menu11.1 Language Menu Feature Description Default Options Enables / disables the on-screen message By the device Enables the user to edit a customized, onArea Parameters Menu Depending on the horizontal position reachedSetting the Area Position Values Changing the Edit Text MenuDisplay Parameters Offset PanSpeed Menu Wiper-washer, and the alarm settings of the UPH11.3 Motion Parameters Menu Tilt Speed Data is expressed as degrees per secondPAN Speed Limits Preset/Patrol/Autopan Feature DescriptionPreset Menu Special Preset Parameters Home Position Reached SpeedPatrol loading of preset positions Start PositionEND Position First Prst SpeedMotions Recall Menu Autopan menu is used to indicate preset position settingsAutopan Wiper-Washer Alarms 11.4 Camera ParametersUPH-2D and UPH-3D Series DinionXF Cameras UPH-Z Series camera module Zoom Parameters MenuFocus Parameters menu is used to enable focus settings Focus Parameters MenuDynamic Masking UPH-Z Series only Parameters Mode Infrared MenuAuto Exposure Parameters Menu Mask NR Mask ChangingPosition Recall Changing ColourPTZ Mode Masking 11.5 Creating a New Dynamic MaskImage Stabilization Back Light CompenSAT 11.6 Load Default Configuration 11.7 Setup Info MenuLoad Default menu is used to load the default settings UPH boardsMaintenance 12.1 Cleaning12.2 Replacing the Fuses Voltage Fuse F1 Fuse F2Troubleshooting Error TroubleshootingProblem Possible Cause Solution 13.1 Dimensions and Range of Movement 514 584R385 Technical Specifications Bosch Security Systems