![](/images/new-backgrounds/1242445/242445119x1.webp)
60 en TroubleshootingHigh Speed Pan/Tilt System
13 | Troubleshooting |
|
|
| |
|
|
|
|
| |
| Problem |
| Possible Cause | Solution | |
|
|
|
|
| |
| The device is switched off | Incorrect wiring, fuses | Make sure all the connections are cor- | ||
| and shows no signs of life. | blown. | rect, check the continuity of the fuses | ||
|
|
|
|
| and, if there is a failure, replace them |
|
|
|
|
| according to the values shown in the |
|
|
|
|
| table. |
|
|
|
|
| NOTE: if the fuses blow repeatedly, |
|
|
|
|
| contact the authorized service centre. |
|
|
|
|
| |
| There is no image on the | Incorrect camera or | Make sure all connections are correct | ||
| screen, just a blue screen | module wiring, camera | for the camera version and motorised | ||
| with the message NO VIDEO | failure. | lenses. | ||
| SIGNAL!!! |
|
|
|
|
|
|
|
|
| |
| Presets are not as accurate | Wind, vibration, and | AUX On - 204 - Enter command recali- | ||
| as they were during installa- | other environmental | brates presets; takes | ||
| tion. |
| conditions. | complete. | |
|
|
|
|
| |
| Under particular zoom con- | The camera is too far | Adjust the camera position by adjusting | ||
| ditions, the housing or sun- | behind the glass. | the slide until the correct position is | ||
| shield interferes with the |
|
| found. | |
| image (only for versions with |
|
|
| |
| motorised lens). |
|
|
|
|
|
|
|
|
| |
| It is too cold for the | Wait for | |||
| the screen and user has no | UPH to safely be used. | plete | ||
| control. |
|
|
|
|
|
|
|
|
| |
| Data transfer stops. | Power spike/fluctua- | Reset power on UPH and the unit | ||
|
|
| tion or spurious noise | recovers, although some OSD changes | |
|
|
| on video/data line. | may be lost and need to be | |
|
|
|
|
| |
| The monitor does NOT show | Programming dip | Switch off the pan & tilt, switch off | ||
| the image photographed by | switch on (up posi- | (down position) the “PROGRAM.” dip | ||
| the UPH, but shows a dis- | tion). | switch | ||
| play similar to Figure . |
|
| baud rate section) and then switch the | |
|
|
|
|
| device on again. |
|
|
|
|
| |
| There is no video. | Wire(s) may be | |||
|
|
| installed incorrectly. | that they are properly secure. | |
|
|
| Monitor input may be | Verify that monitor is displaying the | |
|
|
| on incorrect setting. | correct input setting. | |
|
|
| The motor may be | Remove power to the unit, | |
|
|
| working improperly. | power, and allow the device to go | |
|
|
|
|
| through its homing phase. |
|
|
|
|
|
|
|
|
|
|
|
|
| NET board | MPP board |
|
|
|
| ver. Bosch 1.7 | ver. Bosch 1.7 |
|
|
|
| Apr 27 2007 | Apr 27 2007 |
|
|
|
| HD r.2 | HD r.2 |
|
|
|
| Protocol | :BOSCH |
|
|
|
| Baudrate | :38400 |
|
|
|
| Address | :00001 |
|
|
|
| Enabled RS485 |
|
|
| |
|
|
|
| ||
|
|
|
|
| |
| Troubleshooting Error |
|
|
|
F01U.073.990 Version 1.0 2007.07 | Instruction Manual | Bosch Security Systems |