Bosch Appliances UPH-3D, UPH-2D, UPH-Z Protocol Switches, Setting the Address, Ported are

Page 26

26 en Configuring the DeviceHigh Speed Pan/Tilt System

7.2	Protocol Switches
	There is no need to set any particular protocol, the UPH is auto-sensing. The protocols sup-
	ported are:

	Protocol	Baud Rate	Menu setup (OSD)

	Pelco D	2400	Preset 95
	Pelco D	(8N 1)	Preset 95
		(8N 1)

	Biphase and	Auto	AUX-On 200
	Bilinx		AUX-On 200
	Bilinx

	Table 7.2 Supported Protocols
7.3	Setting the Address

The UPH address can have a setting from 1 to 255. Binary code is used to select the address, using the 8 DIP switches on the far right. The up position represents binary value “1”, while the down position represents binary value “0”.

See Figure 7.2 for all possible combinations (the white rectangle represents the position of the switch).

Serial Lines

Address

Table 7.3 All Possible Settings for Setting the UPH Address

Serial Lines Switches:

Dip-switches 10 and 9 are not used; the unit has fixed serial line mode.

Serial Lines Termination Switches:

Dip-switch 1 is not used (the RS485-1 line is not available).

Dip-switch 2 is used to enable the line termination of RS485-2 serial line.

Bilinx and Biphase Switches:

Dip-switch 1 is used to enable the line termination of Biphase serial line.

Dip-switch 2 is used to select the video format (ON = PAL, OFF = NTSC).

F01U.073.990 Version 1.0 2007.07

Instruction Manual

Bosch Security Systems

Image 26

Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Safety Important safety instructionsSafety precautions Important notices Coax groundingCopyright TrademarksTools Required Parts List2Unpacking Small, straight-blade screwdriver 2.5 mm 0.1Safety Rules 3DescriptionWarranties are void Installing the High Speed Pan/TiltMounting the High Speed Pan/Tilt Outdoor Wall Mount for UPH Series DescriptionOutdoor Pole Mount for UPH Series Pole Adapter for MTC-WUPHReference # Description Base Gasket Screw Ring Washer Bracket SupportWiring the Video Cable Tie Threads used to Group and Secure Signal CablesWire Color VAC Terminal Connection Connecting the Power SupplyThat the disconnecting switch is open Per local Installer Neutral Live/Active Green/Yellow Earth5RS-232 Wiring BiphaseRS-232 is used for firmware upgrades only see Figure Connecting the Washer Pump optional Nosecap Washer PipeNut CouplingCalibrating the Nozzle Reference Description AL1Connecting the Peripherals Base with 19-pin Connector for Connecting PeripheralsSalt Bag Metal Fixing AccessoryAttaching the Top Unit Fixing ScrewsAligning the Tabs Screw Configuration WindowPlace safety label near unit that warns of moving parts Screw SealRocker for DIP switch No is OFF PROGRAM. OFF Configuring the DeviceBaud Rate Switches For updating the firmwareProtocol Baud Rate Menu setup OSD Protocol SwitchesSetting the Address Pelco D 2400 Preset Biphase Auto AUX-On BilinxAddress Combinations 4Connections Intuikeyboard RS-485 Divar BiphaseRS-485 Biphase Bilinx/Video Intuikeyboard AllegiantRS485-2 EthernetEthernet VideoTo configure the UPH, proceed as follows Switching On and OffConfiguring the Device Moving Around the Menus Using the JoystickOn-screen Display OSD Open or Iris Close buttonPresets 10.1 Keyboard Commands ListSetup and Configuration Auxiliary Connections10.3 Changing the Numeric Fields Configuring the System10.2 Changing the Settings Main menu by pressing AUX on 200 EnterPlayed on the screen 11.2 Display Setup Menu11.1 Language Menu Feature Description Default Options Area Parameters Menu Enables / disables the on-screen messageBy the device Enables the user to edit a customized, on Depending on the horizontal position reachedSetting the Area Position Values Changing the Edit Text MenuDisplay Parameters Offset PanSpeed Menu Wiper-washer, and the alarm settings of the UPH11.3 Motion Parameters Menu Tilt Speed Data is expressed as degrees per secondPAN Speed Limits Preset/Patrol/Autopan Feature DescriptionPreset Menu Special Preset Parameters Home Position Reached SpeedEND Position Patrol loading of preset positionsStart Position First Prst SpeedMotions Recall Menu Autopan menu is used to indicate preset position settingsAutopan Wiper-Washer Alarms 11.4 Camera ParametersUPH-2D and UPH-3D Series DinionXF Cameras UPH-Z Series camera module Zoom Parameters MenuFocus Parameters menu is used to enable focus settings Focus Parameters MenuDynamic Masking UPH-Z Series only Parameters Mode Infrared MenuAuto Exposure Parameters Menu Position Recall Mask NRMask Changing Changing ColourPTZ Mode Masking 11.5 Creating a New Dynamic MaskImage Stabilization Back Light CompenSAT Load Default menu is used to load the default settings 11.6 Load Default Configuration11.7 Setup Info Menu UPH boards12.2 Replacing the Fuses Maintenance12.1 Cleaning Voltage Fuse F1 Fuse F2Troubleshooting Error TroubleshootingProblem Possible Cause Solution 13.1 Dimensions and Range of Movement 514 584R385 Technical Specifications Bosch Security Systems