Bosch Appliances UPH-2D, UPH-Z, UPH-3D Back Light Compen, Sat, Image Stabilization

Page 57

High Speed Pan/Tilt System	Configuring the System en 57

Parameters Mode - Various
1	- BACK LIGHT COMPENSAT	NO
2	- IMAGE STABILIZATION	NO

Fig. 11.28 Parameters Mode - Various

Feature	Description	Default	Options

BACK LIGHT COMPEN-	Reduces negative effects from	NO	YES, NO
SAT	bight backlights. This feature is
	scene dependent, therefore, it
	is recommended to test this fea-
	ture on site.

IMAGE STABILIZATION	Turn on this feature when the	NO	YES, NO
	image is affected by vibration
	that causes the picture to move.

Bosch Security Systems

Instruction Manual

F01U.073.990 Version 1.0 2007.07

Image 57

Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Important safety instructions SafetySafety precautions Coax grounding Important noticesTrademarks Copyright2Unpacking Parts ListTools Required Small, straight-blade screwdriver 2.5 mm 0.13Description Safety RulesInstalling the High Speed Pan/Tilt Mounting the High Speed Pan/TiltWarranties are void Outdoor Pole Mount for UPH Series DescriptionOutdoor Wall Mount for UPH Series Pole Adapter for MTC-WUPHBase Gasket Screw Ring Washer Bracket Support Reference # DescriptionTie Threads used to Group and Secure Signal Cables Wiring the Video CableThat the disconnecting switch is open Connecting the Power SupplyWire Color VAC Terminal Connection Per local Installer Neutral Live/Active Green/Yellow EarthWiring Biphase RS-232 is used for firmware upgrades only see Figure5RS-232 Connecting the Washer Pump optional Nut Washer PipeNosecap CouplingCalibrating the Nozzle AL1 Reference DescriptionBase with 19-pin Connector for Connecting Peripherals Connecting the PeripheralsAttaching the Top Unit Metal Fixing AccessorySalt Bag Fixing ScrewsAligning the Tabs Place safety label near unit that warns of moving parts Configuration WindowScrew Screw SealBaud Rate Switches Configuring the DeviceRocker for DIP switch No is OFF PROGRAM. OFF For updating the firmwareSetting the Address Protocol SwitchesProtocol Baud Rate Menu setup OSD Pelco D 2400 Preset Biphase Auto AUX-On BilinxAddress Combinations 4Connections RS-485 Biphase Bilinx/Video Intuikeyboard RS-485 Divar BiphaseIntuikeyboard AllegiantEthernetEthernet Video RS485-2Switching On and Off Configuring the DeviceTo configure the UPH, proceed as follows On-screen Display OSD Using the JoystickMoving Around the Menus Open or Iris Close buttonSetup and Configuration 10.1 Keyboard Commands ListPresets Auxiliary Connections10.2 Changing the Settings Configuring the System10.3 Changing the Numeric Fields Main menu by pressing AUX on 200 Enter11.2 Display Setup Menu 11.1 Language MenuPlayed on the screen Feature Description Default Options By the device Enables the user to edit a customized, on Enables / disables the on-screen messageArea Parameters Menu Depending on the horizontal position reachedChanging the Edit Text Menu Setting the Area Position ValuesOffset Pan Display ParametersWiper-washer, and the alarm settings of the UPH 11.3 Motion Parameters MenuSpeed Menu Data is expressed as degrees per second PAN SpeedTilt Speed Limits Feature Description Preset/Patrol/AutopanPreset Menu Special Preset Parameters Reached Speed Home PositionStart Position Patrol loading of preset positionsEND Position First Prst SpeedAutopan menu is used to indicate preset position settings AutopanMotions Recall Menu Wiper-Washer 11.4 Camera Parameters AlarmsUPH-2D and UPH-3D Series DinionXF Cameras Zoom Parameters Menu UPH-Z Series camera moduleFocus Parameters Menu Focus Parameters menu is used to enable focus settingsParameters Mode Infrared Menu Auto Exposure Parameters MenuDynamic Masking UPH-Z Series only Mask Changing Mask NRPosition Recall Changing Colour11.5 Creating a New Dynamic Mask PTZ Mode MaskingBack Light Compen SATImage Stabilization 11.7 Setup Info Menu 11.6 Load Default ConfigurationLoad Default menu is used to load the default settings UPH boards12.1 Cleaning Maintenance12.2 Replacing the Fuses Voltage Fuse F1 Fuse F2Troubleshooting Problem Possible Cause SolutionTroubleshooting Error 514 584 13.1 Dimensions and Range of MovementR385 Technical Specifications Bosch Security Systems