Bosch Appliances UPH-3D, UPH-2D, UPH-Z instruction manual Connecting the Washer Pump optional

Page 17

High Speed Pan/Tilt SystemConnecting the Washer Pump (optional) en 17

5	Connecting the Washer Pump (optional)

The device must be wired by skilled technical personnel. Never make any

!changes or connections that are not described in this handbook. Failure to fol- low the instructions indicated in this manual may result in system or safety hazards, thus invalidating the guarantee.

The High Speed Pan/Tilt System may have an optional washer pump. To connect the washer pump for the HAC-WAS05-20, HAC-WAS05-50, and HAC-WAS30-50, proceed as follows:

1.Attach the mount, (optional wall or pole mount) by positioning the washer pipe support in the desired position (see Figure 5.1).

Fig. 5.1 Installing the Washer Cables

Reference #	Description

1	Base

2	Cable Glands

3	Washer Pipe Support

4	Gasket

5	Screw Seals

6	Bracket or Pole Support

7	Washers

8	Screws

Bosch Security Systems

Instruction Manual

F01U.073.990 Version 1.0 2007.07

Image 17

Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Important safety instructions SafetySafety precautions Coax grounding Important noticesTrademarks Copyright2Unpacking Parts ListTools Required Small, straight-blade screwdriver 2.5 mm 0.13Description Safety RulesWarranties are void Installing the High Speed Pan/TiltMounting the High Speed Pan/Tilt Outdoor Pole Mount for UPH Series DescriptionOutdoor Wall Mount for UPH Series Pole Adapter for MTC-WUPHBase Gasket Screw Ring Washer Bracket Support Reference # DescriptionTie Threads used to Group and Secure Signal Cables Wiring the Video CableThat the disconnecting switch is open Connecting the Power SupplyWire Color VAC Terminal Connection Per local Installer Neutral Live/Active Green/Yellow Earth5RS-232 Wiring BiphaseRS-232 is used for firmware upgrades only see Figure Connecting the Washer Pump optional Nut Washer PipeNosecap CouplingCalibrating the Nozzle AL1 Reference DescriptionBase with 19-pin Connector for Connecting Peripherals Connecting the PeripheralsAttaching the Top Unit Metal Fixing AccessorySalt Bag Fixing ScrewsAligning the Tabs Place safety label near unit that warns of moving parts Configuration WindowScrew Screw SealBaud Rate Switches Configuring the DeviceRocker for DIP switch No is OFF PROGRAM. OFF For updating the firmwareSetting the Address Protocol SwitchesProtocol Baud Rate Menu setup OSD Pelco D 2400 Preset Biphase Auto AUX-On BilinxAddress Combinations 4Connections RS-485 Biphase Bilinx/Video Intuikeyboard RS-485 Divar BiphaseIntuikeyboard AllegiantEthernetEthernet Video RS485-2To configure the UPH, proceed as follows Switching On and OffConfiguring the Device On-screen Display OSD Using the JoystickMoving Around the Menus Open or Iris Close buttonSetup and Configuration 10.1 Keyboard Commands ListPresets Auxiliary Connections10.2 Changing the Settings Configuring the System10.3 Changing the Numeric Fields Main menu by pressing AUX on 200 EnterPlayed on the screen 11.2 Display Setup Menu11.1 Language Menu Feature Description Default Options By the device Enables the user to edit a customized, on Enables / disables the on-screen messageArea Parameters Menu Depending on the horizontal position reachedChanging the Edit Text Menu Setting the Area Position ValuesOffset Pan Display ParametersSpeed Menu Wiper-washer, and the alarm settings of the UPH11.3 Motion Parameters Menu Tilt Speed Data is expressed as degrees per secondPAN Speed Limits Feature Description Preset/Patrol/AutopanPreset Menu Special Preset Parameters Reached Speed Home PositionStart Position Patrol loading of preset positionsEND Position First Prst SpeedMotions Recall Menu Autopan menu is used to indicate preset position settingsAutopan Wiper-Washer 11.4 Camera Parameters AlarmsUPH-2D and UPH-3D Series DinionXF Cameras Zoom Parameters Menu UPH-Z Series camera moduleFocus Parameters Menu Focus Parameters menu is used to enable focus settingsDynamic Masking UPH-Z Series only Parameters Mode Infrared MenuAuto Exposure Parameters Menu Mask Changing Mask NRPosition Recall Changing Colour11.5 Creating a New Dynamic Mask PTZ Mode MaskingImage Stabilization Back Light CompenSAT 11.7 Setup Info Menu 11.6 Load Default ConfigurationLoad Default menu is used to load the default settings UPH boards12.1 Cleaning Maintenance12.2 Replacing the Fuses Voltage Fuse F1 Fuse F2Troubleshooting Error TroubleshootingProblem Possible Cause Solution 514 584 13.1 Dimensions and Range of MovementR385 Technical Specifications Bosch Security Systems