Bosch Appliances UPH-2D, UPH-Z, UPH-3D instruction manual Feature Description Default Options

Page 36

36 en Configuring the SystemHigh Speed Pan/Tilt System

	Feature	Description	Default	Options

	PAN/TILT POSITION	Shows the current position of the device (in	YES	YES, NO
	PAN/TILT POSITION	degrees) with reference to the home position.	YES	YES, NO

	PRESET TITLE	Enables or disables the preset title on the dis-	YES	YES, NO
	PRESET TITLE	play.	YES	YES, NO
		play.

	PRESET POSITION	Enables or disables the preset number reached	YES	YES, NO
		on the display.

	TILT LIMIT TITLE	Enables or disables displaying if the tilt limit is	YES	YES, NO
	TILT LIMIT TITLE	reached.	YES	YES, NO
		reached.

	VIDEO SIGNAL	Type of video signal.	PAL	PAL, NTSC

	INTERLACED VIDEO	Enables or disables the display for interlaced	YES	YES, NO
		video.
	AREA PARAMETERS	Information about area (or sector) that the unit
		is pointing towards.

	DISPLAY	Setup of location of text position/type on the
	PARAMETERS	display.

NOTICE! Over time, due to environmental factors such as wind and vibration, preset positions may not always align with what they were at installation. Use

i AUX ON - 204 - Enter to correct this. It takes 30-45 seconds to cycle through this process, during which time there is no user control. Once it has finished the process and corrected for the effect of any environmental factors, the user regains full

control.

F01U.073.990 Version 1.0 2007.07

Instruction Manual

Bosch Security Systems

Image 36

Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Safety Important safety instructionsSafety precautions Important notices Coax groundingCopyright TrademarksParts List 2UnpackingTools Required Small, straight-blade screwdriver 2.5 mm 0.1Safety Rules 3DescriptionInstalling the High Speed Pan/Tilt Mounting the High Speed Pan/TiltWarranties are void Description Outdoor Pole Mount for UPH SeriesOutdoor Wall Mount for UPH Series Pole Adapter for MTC-WUPHReference # Description Base Gasket Screw Ring Washer Bracket SupportWiring the Video Cable Tie Threads used to Group and Secure Signal CablesConnecting the Power Supply That the disconnecting switch is openWire Color VAC Terminal Connection Per local Installer Neutral Live/Active Green/Yellow EarthWiring Biphase RS-232 is used for firmware upgrades only see Figure5RS-232 Connecting the Washer Pump optional Washer Pipe NutNosecap CouplingCalibrating the Nozzle Reference Description AL1Connecting the Peripherals Base with 19-pin Connector for Connecting PeripheralsMetal Fixing Accessory Attaching the Top UnitSalt Bag Fixing ScrewsAligning the Tabs Configuration Window Place safety label near unit that warns of moving partsScrew Screw SealConfiguring the Device Baud Rate SwitchesRocker for DIP switch No is OFF PROGRAM. OFF For updating the firmwareProtocol Switches Setting the AddressProtocol Baud Rate Menu setup OSD Pelco D 2400 Preset Biphase Auto AUX-On BilinxAddress Combinations 4Connections RS-485 Divar Biphase RS-485 Biphase Bilinx/Video IntuikeyboardIntuikeyboard AllegiantRS485-2 EthernetEthernet VideoSwitching On and Off Configuring the DeviceTo configure the UPH, proceed as follows Using the Joystick On-screen Display OSDMoving Around the Menus Open or Iris Close button10.1 Keyboard Commands List Setup and ConfigurationPresets Auxiliary ConnectionsConfiguring the System 10.2 Changing the Settings10.3 Changing the Numeric Fields Main menu by pressing AUX on 200 Enter11.2 Display Setup Menu 11.1 Language MenuPlayed on the screen Feature Description Default Options Enables / disables the on-screen message By the device Enables the user to edit a customized, onArea Parameters Menu Depending on the horizontal position reachedSetting the Area Position Values Changing the Edit Text MenuDisplay Parameters Offset PanWiper-washer, and the alarm settings of the UPH 11.3 Motion Parameters MenuSpeed Menu Data is expressed as degrees per second PAN SpeedTilt Speed Limits Preset/Patrol/Autopan Feature DescriptionPreset Menu Special Preset Parameters Home Position Reached SpeedPatrol loading of preset positions Start PositionEND Position First Prst SpeedAutopan menu is used to indicate preset position settings AutopanMotions Recall Menu Wiper-Washer Alarms 11.4 Camera ParametersUPH-2D and UPH-3D Series DinionXF Cameras UPH-Z Series camera module Zoom Parameters MenuFocus Parameters menu is used to enable focus settings Focus Parameters MenuParameters Mode Infrared Menu Auto Exposure Parameters MenuDynamic Masking UPH-Z Series only Mask NR Mask ChangingPosition Recall Changing ColourPTZ Mode Masking 11.5 Creating a New Dynamic MaskBack Light Compen SATImage Stabilization 11.6 Load Default Configuration 11.7 Setup Info MenuLoad Default menu is used to load the default settings UPH boardsMaintenance 12.1 Cleaning12.2 Replacing the Fuses Voltage Fuse F1 Fuse F2Troubleshooting Problem Possible Cause SolutionTroubleshooting Error 13.1 Dimensions and Range of Movement 514 584R385 Technical Specifications Bosch Security Systems