Bosch Appliances UPH-3D, UPH-2D, UPH-Z instruction manual R385

Page 62

62 en Troubleshooting	High Speed Pan/Tilt System

514 (20.24)
40º
-
90º
R350
(13.
78)
724 (28.50)
73
(2.87)
(14.72)374
R385
(15
.
16)

Fig. 13.1 Dimensions and Range of Movement

F01U.073.990 Version 1.0 2007.07

Instruction Manual

Bosch Security Systems

Image 62

Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Safety Important safety instructionsSafety precautions Important notices Coax groundingCopyright TrademarksTools Required Parts List2Unpacking Small, straight-blade screwdriver 2.5 mm 0.1Safety Rules 3DescriptionWarranties are void Installing the High Speed Pan/TiltMounting the High Speed Pan/Tilt Outdoor Wall Mount for UPH Series DescriptionOutdoor Pole Mount for UPH Series Pole Adapter for MTC-WUPHReference # Description Base Gasket Screw Ring Washer Bracket SupportWiring the Video Cable Tie Threads used to Group and Secure Signal CablesWire Color VAC Terminal Connection Connecting the Power SupplyThat the disconnecting switch is open Per local Installer Neutral Live/Active Green/Yellow Earth5RS-232 Wiring BiphaseRS-232 is used for firmware upgrades only see Figure Connecting the Washer Pump optional Nosecap Washer PipeNut CouplingCalibrating the Nozzle Reference Description AL1Connecting the Peripherals Base with 19-pin Connector for Connecting PeripheralsSalt Bag Metal Fixing AccessoryAttaching the Top Unit Fixing ScrewsAligning the Tabs Screw Configuration WindowPlace safety label near unit that warns of moving parts Screw SealRocker for DIP switch No is OFF PROGRAM. OFF Configuring the DeviceBaud Rate Switches For updating the firmwareProtocol Baud Rate Menu setup OSD Protocol SwitchesSetting the Address Pelco D 2400 Preset Biphase Auto AUX-On BilinxAddress Combinations 4Connections Intuikeyboard RS-485 Divar BiphaseRS-485 Biphase Bilinx/Video Intuikeyboard AllegiantRS485-2 EthernetEthernet VideoTo configure the UPH, proceed as follows Switching On and OffConfiguring the Device Moving Around the Menus Using the JoystickOn-screen Display OSD Open or Iris Close buttonPresets 10.1 Keyboard Commands ListSetup and Configuration Auxiliary Connections10.3 Changing the Numeric Fields Configuring the System10.2 Changing the Settings Main menu by pressing AUX on 200 EnterPlayed on the screen 11.2 Display Setup Menu11.1 Language Menu Feature Description Default Options Area Parameters Menu Enables / disables the on-screen messageBy the device Enables the user to edit a customized, on Depending on the horizontal position reachedSetting the Area Position Values Changing the Edit Text MenuDisplay Parameters Offset PanSpeed Menu Wiper-washer, and the alarm settings of the UPH11.3 Motion Parameters Menu Tilt Speed Data is expressed as degrees per secondPAN Speed Limits Preset/Patrol/Autopan Feature DescriptionPreset Menu Special Preset Parameters Home Position Reached SpeedEND Position Patrol loading of preset positionsStart Position First Prst SpeedMotions Recall Menu Autopan menu is used to indicate preset position settingsAutopan Wiper-Washer Alarms 11.4 Camera ParametersUPH-2D and UPH-3D Series DinionXF Cameras UPH-Z Series camera module Zoom Parameters MenuFocus Parameters menu is used to enable focus settings Focus Parameters MenuDynamic Masking UPH-Z Series only Parameters Mode Infrared MenuAuto Exposure Parameters Menu Position Recall Mask NRMask Changing Changing ColourPTZ Mode Masking 11.5 Creating a New Dynamic MaskImage Stabilization Back Light CompenSAT Load Default menu is used to load the default settings 11.6 Load Default Configuration11.7 Setup Info Menu UPH boards12.2 Replacing the Fuses Maintenance12.1 Cleaning Voltage Fuse F1 Fuse F2Troubleshooting Error TroubleshootingProblem Possible Cause Solution 13.1 Dimensions and Range of Movement 514 584R385 Technical Specifications Bosch Security Systems