Bosch Appliances UPH-Z, UPH-2D, UPH-3D Load Default Configuration, Setup Info Menu, UPH boards

Page 58

58 en Configuring the SystemHigh Speed Pan/Tilt System

11.6

Load Default Configuration

 

The Load Default menu is used to load the default settings.

 

 

 

 

 

DEFAULT VALUES MENU

 

 

 

1

- LOAD DEF. VALUES?

YES

 

2

- DELETE ALL PRST?

NO

ATTENTION!!!

RELOAD ALL SETTINGS

EXCEPT FOR PRESETS

Fig. 11.29 Load Default Menu

DEFAULT VALUES MENU

 

1

- LOAD DEF. VALUES?

NO

2

- DELETE ALL PRST?

YES

ATTENTION!!!

CLEARS ONLY THE PRESETS

Fig. 11.30 Clear All Presets

11.7

Setup Info Menu

 

The Setup Info menu is used to check the device configuration and the software versions of

 

the UPH boards.

 

 

 

 

 

 

 

 

SETUP INFO MENU

 

 

 

NET board

:

MPP board:

 

 

ver. BOSCH 1.7

 

ver. BOSCH 1.7

 

 

Apr. 27 2007

 

Apr. 27 2007

 

 

HD r.2

 

HD r.2

 

 

Protocol

:

BOSCH

 

 

Baudrate

:

38400

 

 

Address

:

00001

 

 

Enabled RS485

:

TX-RX

 

 

FWInt 01.03

 

FWCam: 01.00

 

 

 

 

 

 

Fig. 11.31 Setup Info Menu

F01U.073.990 Version 1.0 2007.07

Instruction Manual

Bosch Security Systems

Page 57 Page 59
Image 58
Page 57 Page 59
Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Safety Important safety instructionsSafety precautions Important notices Coax groundingCopyright TrademarksTools Required Parts List2Unpacking Small, straight-blade screwdriver 2.5 mm 0.1Safety Rules 3DescriptionMounting the High Speed Pan/Tilt Installing the High Speed Pan/TiltWarranties are void Outdoor Wall Mount for UPH Series DescriptionOutdoor Pole Mount for UPH Series Pole Adapter for MTC-WUPHReference # Description Base Gasket Screw Ring Washer Bracket SupportWiring the Video Cable Tie Threads used to Group and Secure Signal CablesWire Color VAC Terminal Connection Connecting the Power SupplyThat the disconnecting switch is open Per local Installer Neutral Live/Active Green/Yellow EarthRS-232 is used for firmware upgrades only see Figure Wiring Biphase5RS-232 Connecting the Washer Pump optional Nosecap Washer PipeNut CouplingCalibrating the Nozzle Reference Description AL1Connecting the Peripherals Base with 19-pin Connector for Connecting PeripheralsSalt Bag Metal Fixing AccessoryAttaching the Top Unit Fixing ScrewsAligning the Tabs Screw Configuration WindowPlace safety label near unit that warns of moving parts Screw SealRocker for DIP switch No is OFF PROGRAM. OFF Configuring the DeviceBaud Rate Switches For updating the firmwareProtocol Baud Rate Menu setup OSD Protocol SwitchesSetting the Address Pelco D 2400 Preset Biphase Auto AUX-On BilinxAddress Combinations 4Connections Intuikeyboard RS-485 Divar BiphaseRS-485 Biphase Bilinx/Video Intuikeyboard AllegiantRS485-2 EthernetEthernet VideoConfiguring the Device Switching On and OffTo configure the UPH, proceed as follows Moving Around the Menus Using the JoystickOn-screen Display OSD Open or Iris Close buttonPresets 10.1 Keyboard Commands ListSetup and Configuration Auxiliary Connections10.3 Changing the Numeric Fields Configuring the System10.2 Changing the Settings Main menu by pressing AUX on 200 Enter11.1 Language Menu 11.2 Display Setup MenuPlayed on the screen Feature Description Default Options Area Parameters Menu Enables / disables the on-screen messageBy the device Enables the user to edit a customized, on Depending on the horizontal position reachedSetting the Area Position Values Changing the Edit Text MenuDisplay Parameters Offset Pan11.3 Motion Parameters Menu Wiper-washer, and the alarm settings of the UPHSpeed Menu PAN Speed Data is expressed as degrees per secondTilt Speed Limits Preset/Patrol/Autopan Feature DescriptionPreset Menu Special Preset Parameters Home Position Reached SpeedEND Position Patrol loading of preset positionsStart Position First Prst SpeedAutopan Autopan menu is used to indicate preset position settingsMotions Recall Menu Wiper-Washer Alarms 11.4 Camera ParametersUPH-2D and UPH-3D Series DinionXF Cameras UPH-Z Series camera module Zoom Parameters MenuFocus Parameters menu is used to enable focus settings Focus Parameters MenuAuto Exposure Parameters Menu Parameters Mode Infrared MenuDynamic Masking UPH-Z Series only Position Recall Mask NRMask Changing Changing ColourPTZ Mode Masking 11.5 Creating a New Dynamic MaskSAT Back Light CompenImage Stabilization Load Default menu is used to load the default settings 11.6 Load Default Configuration11.7 Setup Info Menu UPH boards12.2 Replacing the Fuses Maintenance12.1 Cleaning Voltage Fuse F1 Fuse F2Problem Possible Cause Solution TroubleshootingTroubleshooting Error 13.1 Dimensions and Range of Movement 514 584R385 Technical Specifications Bosch Security Systems
Top Page Image Contents