Bosch Appliances UPH-Z, UPH-2D, UPH-3D instruction manual Calibrating the Nozzle

Page 19

High Speed Pan/Tilt System	Connecting the Washer Pump (optional) en 19

1

Fig. 5.3 Calibrating the Nozzle

The diagram below refers to the 19-pin connector on the base board of the pan/tilt.

Fig. 5.4 Connecting the Washer Pump

Bosch Security Systems

Instruction Manual

F01U.073.990 Version 1.0 2007.07

Image 19

Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Important safety instructions SafetySafety precautions Coax grounding Important noticesTrademarks CopyrightSmall, straight-blade screwdriver 2.5 mm 0.1 Parts List2Unpacking Tools Required3Description Safety RulesMounting the High Speed Pan/Tilt Installing the High Speed Pan/TiltWarranties are void Pole Adapter for MTC-WUPH DescriptionOutdoor Pole Mount for UPH Series Outdoor Wall Mount for UPH SeriesBase Gasket Screw Ring Washer Bracket Support Reference # DescriptionTie Threads used to Group and Secure Signal Cables Wiring the Video CablePer local Installer Neutral Live/Active Green/Yellow Earth Connecting the Power SupplyThat the disconnecting switch is open Wire Color VAC Terminal ConnectionRS-232 is used for firmware upgrades only see Figure Wiring Biphase5RS-232 Connecting the Washer Pump optional Coupling Washer PipeNut NosecapCalibrating the Nozzle AL1 Reference DescriptionBase with 19-pin Connector for Connecting Peripherals Connecting the PeripheralsFixing Screws Metal Fixing AccessoryAttaching the Top Unit Salt BagAligning the Tabs Screw Seal Configuration WindowPlace safety label near unit that warns of moving parts ScrewFor updating the firmware Configuring the DeviceBaud Rate Switches Rocker for DIP switch No is OFF PROGRAM. OFFPelco D 2400 Preset Biphase Auto AUX-On Bilinx Protocol SwitchesSetting the Address Protocol Baud Rate Menu setup OSDAddress Combinations 4Connections Allegiant RS-485 Divar BiphaseRS-485 Biphase Bilinx/Video Intuikeyboard IntuikeyboardEthernetEthernet Video RS485-2Configuring the Device Switching On and OffTo configure the UPH, proceed as follows Open or Iris Close button Using the JoystickOn-screen Display OSD Moving Around the MenusAuxiliary Connections 10.1 Keyboard Commands ListSetup and Configuration PresetsMain menu by pressing AUX on 200 Enter Configuring the System10.2 Changing the Settings 10.3 Changing the Numeric Fields11.1 Language Menu 11.2 Display Setup MenuPlayed on the screen Feature Description Default Options Depending on the horizontal position reached Enables / disables the on-screen messageBy the device Enables the user to edit a customized, on Area Parameters MenuChanging the Edit Text Menu Setting the Area Position ValuesOffset Pan Display Parameters11.3 Motion Parameters Menu Wiper-washer, and the alarm settings of the UPHSpeed Menu PAN Speed Data is expressed as degrees per secondTilt Speed Limits Feature Description Preset/Patrol/AutopanPreset Menu Special Preset Parameters Reached Speed Home PositionFirst Prst Speed Patrol loading of preset positionsStart Position END PositionAutopan Autopan menu is used to indicate preset position settingsMotions Recall Menu Wiper-Washer 11.4 Camera Parameters AlarmsUPH-2D and UPH-3D Series DinionXF Cameras Zoom Parameters Menu UPH-Z Series camera moduleFocus Parameters Menu Focus Parameters menu is used to enable focus settingsAuto Exposure Parameters Menu Parameters Mode Infrared MenuDynamic Masking UPH-Z Series only Changing Colour Mask NRMask Changing Position Recall11.5 Creating a New Dynamic Mask PTZ Mode MaskingSAT Back Light CompenImage Stabilization UPH boards 11.6 Load Default Configuration11.7 Setup Info Menu Load Default menu is used to load the default settingsVoltage Fuse F1 Fuse F2 Maintenance12.1 Cleaning 12.2 Replacing the FusesProblem Possible Cause Solution TroubleshootingTroubleshooting Error 514 584 13.1 Dimensions and Range of MovementR385 Technical Specifications Bosch Security Systems