Bosch Appliances UPH-2D, UPH-Z, UPH-3D instruction manual Technical Specifications

Page 63

High Speed Pan/Tilt SystemTechnical Specifications en 63

14	Technical Specifications

Horizontal movement (Pan)		Continuous rotation

Vertical movement (Tilt)		+90 ° / -40 °

Horizontal pan speed		Variable from 0.1 °/s to 100 °/s

Vertical tilt speed		Variable from 0.1 °/s to 40 °/s

Operating temperature		UPH-Z Series: -20 °C to +40 °C
		UPH-2D Series: -20 °C to +40 °C
		UHP-3D Series: -20 °C to +40 °C

Power supply		230 VAC 50/60 Hz
		24 VAC 50/60 Hz

Current consumption		0.5 A (230 VAC)
		4.0 A (24 VAC)

Input line cable dimension		AWG: 16-30

Signal cable dimension		AWG: 20-28

Alarm input (voltage-controlled)		10-35 VDC

Clean contact		Maximum 50 VDC or 30 VAC @ 1A

Video line type		Coaxial cable (1 Vpp, 75 Ohm)

Paint		RAL 7035 (light grey) with epoxy powder

Construction		Die-cast aluminum, outer body in ABS

Protection		IP66
		IEC 60529

Weight (unit only)		14 kg

Dimensions		258 x 584 x 514 mm (W x H x D)

Table 14.1	Technical Specifications for the High Speed Pan/Tilt System

Bosch Security Systems

Instruction Manual

F01U.073.990 Version 1.0 2007.07

Image 63

Contents High Speed Pan/Tilt System Page Table of Contents Configuring the System Important safety instructions SafetySafety precautions Coax grounding Important noticesTrademarks CopyrightSmall, straight-blade screwdriver 2.5 mm 0.1 Parts List2Unpacking Tools Required3Description Safety RulesInstalling the High Speed Pan/Tilt Mounting the High Speed Pan/TiltWarranties are void Pole Adapter for MTC-WUPH DescriptionOutdoor Pole Mount for UPH Series Outdoor Wall Mount for UPH SeriesBase Gasket Screw Ring Washer Bracket Support Reference # DescriptionTie Threads used to Group and Secure Signal Cables Wiring the Video CablePer local Installer Neutral Live/Active Green/Yellow Earth Connecting the Power SupplyThat the disconnecting switch is open Wire Color VAC Terminal ConnectionWiring Biphase RS-232 is used for firmware upgrades only see Figure5RS-232 Connecting the Washer Pump optional Coupling Washer PipeNut NosecapCalibrating the Nozzle AL1 Reference DescriptionBase with 19-pin Connector for Connecting Peripherals Connecting the PeripheralsFixing Screws Metal Fixing AccessoryAttaching the Top Unit Salt BagAligning the Tabs Screw Seal Configuration WindowPlace safety label near unit that warns of moving parts ScrewFor updating the firmware Configuring the DeviceBaud Rate Switches Rocker for DIP switch No is OFF PROGRAM. OFFPelco D 2400 Preset Biphase Auto AUX-On Bilinx Protocol SwitchesSetting the Address Protocol Baud Rate Menu setup OSDAddress Combinations 4Connections Allegiant RS-485 Divar BiphaseRS-485 Biphase Bilinx/Video Intuikeyboard IntuikeyboardEthernetEthernet Video RS485-2Switching On and Off Configuring the DeviceTo configure the UPH, proceed as follows Open or Iris Close button Using the JoystickOn-screen Display OSD Moving Around the MenusAuxiliary Connections 10.1 Keyboard Commands ListSetup and Configuration PresetsMain menu by pressing AUX on 200 Enter Configuring the System10.2 Changing the Settings 10.3 Changing the Numeric Fields11.2 Display Setup Menu 11.1 Language MenuPlayed on the screen Feature Description Default Options Depending on the horizontal position reached Enables / disables the on-screen messageBy the device Enables the user to edit a customized, on Area Parameters MenuChanging the Edit Text Menu Setting the Area Position ValuesOffset Pan Display ParametersWiper-washer, and the alarm settings of the UPH 11.3 Motion Parameters MenuSpeed Menu Data is expressed as degrees per second PAN SpeedTilt Speed Limits Feature Description Preset/Patrol/AutopanPreset Menu Special Preset Parameters Reached Speed Home PositionFirst Prst Speed Patrol loading of preset positionsStart Position END PositionAutopan menu is used to indicate preset position settings AutopanMotions Recall Menu Wiper-Washer 11.4 Camera Parameters AlarmsUPH-2D and UPH-3D Series DinionXF Cameras Zoom Parameters Menu UPH-Z Series camera moduleFocus Parameters Menu Focus Parameters menu is used to enable focus settingsParameters Mode Infrared Menu Auto Exposure Parameters MenuDynamic Masking UPH-Z Series only Changing Colour Mask NRMask Changing Position Recall11.5 Creating a New Dynamic Mask PTZ Mode MaskingBack Light Compen SATImage Stabilization UPH boards 11.6 Load Default Configuration11.7 Setup Info Menu Load Default menu is used to load the default settingsVoltage Fuse F1 Fuse F2 Maintenance12.1 Cleaning 12.2 Replacing the FusesTroubleshooting Problem Possible Cause SolutionTroubleshooting Error 514 584 13.1 Dimensions and Range of MovementR385 Technical Specifications Bosch Security Systems