Elite Real AXIOM manual Important Points, Minimum System Requirements

Page 13

GB

IMPORTANT

Never brake when using the RealAxiom trainer, as this could permanently damage the Elastogel roller and the tyre.

For training with the RealAxiom use slick tyres with rigid carcass of 23 mm or wider. The pressure must be 7-8 atm / 100-120 psi for racing wheels (4 atm for MTB wheels). A tyre that is too narrow and insufficient pressure will cause increased wear of the Elastogel roller and the tyre.

Use slick tyres also on MTBs (this will improve grip, reduce noise and wear).

Pay attention to the pressure between tyre and roller: tighten the plate adjustment screw three complete turns from when the roller touches the tyre. If the tyre still slips on the roller, tighten the screw another turn and make the pressure on the pedal more progressive. Training with the tyre slipping will permanently damage the Elastogel roller and the tyre.

During use of the RealAxiom with Elastogel roller, slight wear of the roller is to be considered normal. Tests carried out at Elite have shown that after continuous use for 20000 Km, the wear on the roller is about 0.1 mm. As the total thickness is 15 mm, even far higher wear does not prevent correct operation of the cycle-simulator. Warranty claims resulting from improper or negligent use will not be acknowledged.

The console that is fitted on the handlebar is not waterproof. Take care not to sweat over the console, as the sweat could damage the electronic circuit.

Do not keep the RealAxiom in wet or damp places. This could damage the electronic components.

IMPORTANT POINTS

If placed near TV’s, radios and motors, the equipment generates strong magnetic waves and interference that may give rise to incorrect readings.

Do not use the device and the console within a distance of about one and a half metres from other transmitters.

Do not use other wireless equipment at the same time. This may give rise to incorrect measurements.

Do not expose the unit and the console to direct sunlight for long periods when they are not in use.

Check the position and assembly conditions of the frequency sensor and magnet at regular intervals.

Never use chemical detergents (benzene or thinners) on any part of the Elite RealAxiom.

Minimum System Requirements:

Processor:

Pentium 3

Operative System:

Windows 2000 / XP / Vista

Hard disk:

10 GB7200 rpm

Ram:

256 Mb

Monitor:

800x600

Drive:

DVD-ROM

Ports:

I/O USB

13

Image 13
Contents Page Using Realaxiom with Computer Assembling Instructions Using Realaxiom Without ComputerIntroduzione Istruzioni DI AssemblaggioIntroducción Assemblage DU SupportUSO DEL Realaxiom SIN Ordenador InleidingIstruzioni DEL Software IntroduzioneCardiofrequenzimetro PendenzaRequisiti minimi del sistema ImportanteNome E Lista DEI Componenti Istruzioni DI Assemblaggio Schema Generale SemplificatoAssemblaggio Cavalletto Montaggio UnitàMontaggio Bici SUL Cavalletto Montaggio Sensore DI Cadenza Montaggio Console SUL ManubrioConnessione Cavi Utilizzo DEL Realaxiom Senza ComputerInstallazione Delle Videocorse Installazione DEL Programma DEL RealaxiomUtilizzo DEL Realaxiom CON IL Computer Informazioni Sullo Smaltimento DEL ProdottoSoftware Instructions IntroductionHeart Rate Monitor SlopeMinimum System Requirements Important PointsFeet Parts ListAssembling Instructions Semplified General DiagramAssembling the Stand Assembling the UnitMounting the Bike on the Stand Assembly of the Cadence Sensor Assembly of the Console To the HandlebarComputer Before Installing Using Realaxiom Without ComputerRealaxiom Software Installing the Realaxiom Programme Using Realaxiom with ComputerInstalling the Realaxiom Video Course Information on the Disposal of the ProductSOFTWARE-ANLEITUNG Allgemeine InformationenHerzfrequenzmesser SteigungHinweis Wichtiger HinweisMindestausstattung PC Netzgerät Bezeichnung UND Verzeichnis DER KomponentenMontageanleitung Allgemeines Vereinfachtes SchemaZusammenbau VOM Ständer Montage DER WiderstandseinheitMontage VOM Fahrrad AUF DEM Ständer Montage DER Konsole AM Lenker Montage VOM TrittfrequenzsensorAnschliessen DER Kabel Gebrauch VOM Realaxiom Ohne ComputerInstallierung DER VIDEO-RENNEN Installation DER REALAXIOM-SOFTWAREGebrauch VOM Realaxiom MIT Computer Hinweise ZUR Entsorgung DES ProduktsCARDIO-FREQUENCEMETRE Mode D’EMPLOI DU LogicielPente Conditions minimums requises du systeme RemarquesNOM ET Liste DES Pieces Instructions Pour L’ASSEMBLAGE Schema General SimplifieAssemblage DU Support Montage DE L’UNITÉMontage DU Velo SUR LE Support Montage DU Capteur DE Cadence Montage DE LA Console SUR LE GuidonBranchement DES Fils Utilisation DE Realaxiom Sans OrdinateurInstallation DES Video Courses Installation DU Logiciel DE RealaxiomUtilisation DE Realaxiom Avec Ordinateur Informations SUR L’ELIMINATION DU ProduitInstrucciones DEL Software IntroducciónFrecuencia Cardiaca PendienteRequisitos mínimos del sistema NotasCable CONSOLA-UNIDAD DE Resistencia 8 Polos Nombre Y Relación DE LOS ComponentesEsquema General Simplificado Instrucciones DE EnsamblajeEnsamblaje Caballete Montaje UnidadMontaje Bici Sobre EL Caballete Montaje Consola EN EL Manillar Montaje Detector DE CadenciaConexión Cables USO DEL Realaxiom SIN OrdenadorOrdenador SIN Haber Instalado Antes EL Instalación DEL Programa DEL Realaxiom USO DEL Realaxiom CON EL OrdenadorInstalación DE LOS VIDEO-CARRERAS EN LA Unión EuropeaAanwijzingen M.B.T DE Software InleidingHartslagmeter HellingAandachtspunten BelangrijkKabel Tussen Console EN Weerstandsunit OnderdelenlijstMontagevoorschriften Vereenvoudigd Algemeen DiagramHET Frame Assembleren DE Unit AssemblerenDE Fiets in HET Frame Plaatsen DE Console OP HET Stuur Plaatsen DE Kadanssensor MonterenKabelverbindingen DE Realaxiom Gebruiken Zonder ComputerDE Realaxiom Videorit Installeren HET Realaxiom Programma InstallerenDE Realaxiom Gebruiken MET Computer Informatie Over DE Vernietiging VAN HET ProductGaranzia Garantia Page