Elite Real AXIOM manual Assembly of the Console To the Handlebar, Assembly of the Cadence Sensor

Page 17

ASSEMBLY OF THE CONSOLE

TO THE HANDLEBAR

Attach the bracket to the handlebar, preferably close to the stem. To block the bracket, position the bolt lever as shown in illustration 8. The bolt regulation of the bracket can be adjusted for a secure fix to the handlebar. It may be necessary to remove one or both the rubber shims from the bracket in order to fit larger diameter handlebars.

Illustration 9 shows the correct position of the console mounted to the handlebar.

Check the console is securely fixed to the handlebar and slightly inclined before starting.

9

GB

MAGNET	CLAMP
CLAMP	SENSOR
CLAMP
	CLAMP

10

ASSEMBLY OF THE CADENCE SENSOR

The cadence sensor 6 counts the number of pedal strokes per minute made during the course. It is fitted to the frame of the bike while the magnet 7 is fitted to the pedal crank.

Some plastic clamps 8 are supplied for fixing the sensor, the magnet and the cable to the bike.

How to fit the cadence sensor

Fix the sensor 6 to the horizontal tube connecting the central mechanism to the axis of the rear wheel (left-hand side). Use 2 clamps 8 as shown in illustration 10.

Before tightening the clamps complete the assembly of the magnet and verify the correct functioning during a trial course. If the sensor doesn’t function correctly it could be possible that the magnet is positioned too far from the sensor. In this case push the sensor closer to the magnet by sliding the magnet and the sensor towards the axis of the rear wheel (illustration 11).

11

Procedure for fitting the magnet

Fit a tight clamp 8 into the magnet 7.

	Then place the magnet and clamp on the crank
	and tighten the clamp (illustration 12 and 13).
	Use	the	other
	clamps in the pack
	to fix	the	sensor
	cable to the frame
	of the bike in order
	to prevent		it	from
	touching the			spo-
	kes of the wheel or
	the pedal crank.				12
	Several clamps are				12
	Several clamps are
	supplied with			the
	RealAxiom and not
	all of them need to
	be used.

13

17

Image 17

Contents Page Using Realaxiom with Computer Assembling Instructions Using Realaxiom Without ComputerIntroduzione Istruzioni DI AssemblaggioIntroducción Assemblage DU SupportUSO DEL Realaxiom SIN Ordenador InleidingIstruzioni DEL Software IntroduzioneCardiofrequenzimetro PendenzaRequisiti minimi del sistema ImportanteNome E Lista DEI Componenti Istruzioni DI Assemblaggio Schema Generale SemplificatoAssemblaggio Cavalletto Montaggio UnitàMontaggio Bici SUL Cavalletto Montaggio Sensore DI Cadenza Montaggio Console SUL ManubrioConnessione Cavi Utilizzo DEL Realaxiom Senza ComputerInstallazione Delle Videocorse Installazione DEL Programma DEL RealaxiomUtilizzo DEL Realaxiom CON IL Computer Informazioni Sullo Smaltimento DEL ProdottoSoftware Instructions IntroductionHeart Rate Monitor SlopeMinimum System Requirements Important PointsFeet Parts ListAssembling Instructions Semplified General DiagramAssembling the Stand Assembling the UnitMounting the Bike on the Stand Assembly of the Cadence Sensor Assembly of the Console To the HandlebarRealaxiom Software Using Realaxiom Without ComputerComputer Before Installing Installing the Realaxiom Programme Using Realaxiom with ComputerInstalling the Realaxiom Video Course Information on the Disposal of the ProductSOFTWARE-ANLEITUNG Allgemeine InformationenHerzfrequenzmesser SteigungMindestausstattung PC Wichtiger HinweisHinweis Netzgerät Bezeichnung UND Verzeichnis DER KomponentenMontageanleitung Allgemeines Vereinfachtes SchemaZusammenbau VOM Ständer Montage DER WiderstandseinheitMontage VOM Fahrrad AUF DEM Ständer Montage DER Konsole AM Lenker Montage VOM TrittfrequenzsensorAnschliessen DER Kabel Gebrauch VOM Realaxiom Ohne ComputerInstallierung DER VIDEO-RENNEN Installation DER REALAXIOM-SOFTWAREGebrauch VOM Realaxiom MIT Computer Hinweise ZUR Entsorgung DES ProduktsPente Mode D’EMPLOI DU LogicielCARDIO-FREQUENCEMETRE Conditions minimums requises du systeme RemarquesNOM ET Liste DES Pieces Instructions Pour L’ASSEMBLAGE Schema General SimplifieAssemblage DU Support Montage DE L’UNITÉMontage DU Velo SUR LE Support Montage DU Capteur DE Cadence Montage DE LA Console SUR LE GuidonBranchement DES Fils Utilisation DE Realaxiom Sans OrdinateurInstallation DES Video Courses Installation DU Logiciel DE RealaxiomUtilisation DE Realaxiom Avec Ordinateur Informations SUR L’ELIMINATION DU ProduitInstrucciones DEL Software IntroducciónFrecuencia Cardiaca PendienteRequisitos mínimos del sistema NotasCable CONSOLA-UNIDAD DE Resistencia 8 Polos Nombre Y Relación DE LOS ComponentesEsquema General Simplificado Instrucciones DE EnsamblajeEnsamblaje Caballete Montaje UnidadMontaje Bici Sobre EL Caballete Montaje Consola EN EL Manillar Montaje Detector DE CadenciaOrdenador SIN Haber Instalado Antes EL USO DEL Realaxiom SIN OrdenadorConexión Cables Instalación DEL Programa DEL Realaxiom USO DEL Realaxiom CON EL OrdenadorInstalación DE LOS VIDEO-CARRERAS EN LA Unión EuropeaAanwijzingen M.B.T DE Software InleidingHartslagmeter HellingAandachtspunten BelangrijkKabel Tussen Console EN Weerstandsunit OnderdelenlijstMontagevoorschriften Vereenvoudigd Algemeen DiagramHET Frame Assembleren DE Unit AssemblerenDE Fiets in HET Frame Plaatsen DE Console OP HET Stuur Plaatsen DE Kadanssensor MonterenKabelverbindingen DE Realaxiom Gebruiken Zonder ComputerDE Realaxiom Videorit Installeren HET Realaxiom Programma InstallerenDE Realaxiom Gebruiken MET Computer Informatie Over DE Vernietiging VAN HET ProductGaranzia Garantia Page