Lowrance electronic LMF-200 manual To access the Nmea Information screen, System Information

Page 29

NMEA Info

The NMEA information screen displays information about your NMEA network, including address, instance, serial number and database version.

To access the NMEA Information screen:

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight NMEA INFO and press MENU. The menu will time out and you will be directed to the main display.

System Information

Access the system information screen to see what version of software you have in your LMF-200.

To access System Information screen:

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight SYS INFO and press MENU. The menu will time out and you will be taken back to the main display.

Engine Data

The Engine Data feature allows you to select an engine (Port, Center or Starboard) to be the engine shown on pages that display engine data.

To modify Engine Data:

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight ENG DATA and press MENU. The Engine Data menu will appear with up to three options: Port, Center and Starboard — depending on the number of engines you chose during Boat Setup.

3.Select the engine to be displayed (Port, Center or Starboard) and press MENU. If, for example, you chose the Port engine, the following confirmation message would appear: Hit Menu to chg to Port.

4.Press MENU. You will be taken back to the main display. Pages that display engine data will now show data from the selected engine.

Engine Warnings

The Engine Warnings feature allows you to set an alarm for one or more engines. There are up to five options in the Engine Alarms menu, depending on the number of engines chose during Boat Setup. The options are All Engines, Port, Center, Starboard and Off. The default setting is All Engines. (If you have a single-engine configuration, the only options on the Engine Warning menu will be on and off.)

23

Image 29
Contents LMF-200 Visit our web site Copyright 2006 Lowrance Electronics, Inc All rights reservedTable of Contents Backlight Sync BL Sync Iii Page Introduction Page Recommended Tools and Supplies PreparationMounting the Gauge Installation SequenceWiring LMF-200 cable connections Network Backbone and Network Nodes Connecting to a Nmea 2000 NetworkCompatibility Adding a Network Node Additional Network Information Understanding this Manual Menu CommandsUp and Down keys Menu keyTo execute Boat Setup Boat SetupPages TimeoutBasic Menu Options Viewing Pages Page Screen RotationPages Menu Remove To add a page to the displayTo remove a page from the display AutoscrollTo set a Pop-Up Pop-ups SetupStay Time To set Stay TimeEngine Trim Threshold set up RPM Threshold set upTrim Tabs Threshold set up Pop-up ThresholdsTo adjust Backlight Rudder Threshold set upScreen BacklightTo adjust Contrast Audio SetupContrast Reverse Video Rev VideoSystem Setup Menu To set the Deep Alarm Sonar AlarmsTo set the Shallow Alarm To reset Eng/Tank configuration TimeoutReset To reset valuesTo access System Information screen To access the Nmea Information screenNmea Info System InformationSpeed Range To set Engine WarningsTo set Speed Range Pressure RangeTo change Speed and Distance units To set Pressure RangeUnits To change Pressure units To change Temperature unitsTo change Depth units To change GPS unitsTo change Volume units Fuel SetupRefill Tank Refill T To refill tankEconomy Speed Eco spd To use Partial FillTo change Economy Speed Source Fuel Remaining Source FRem SrcCustomizing Pages To customize the Single Digital To Customize the Gauge To customize the Dual DigitalTo Customize Trim Tabs To Customize the Fuel ManagerTo configure EP-35 Temp Sensor EP-35 Temperature ConfigurationIf all temps configured Configuration name unavailable To unconfigure EP-35 temp sensorTo reconfigure an EP-35 temp sensor If desired configuration name available EP-10 Fuel Flow ConfigurationTo unconfigure an EP-10 Fuel Flow To configure Fuel FlowIf all fuel flows configured Configuration name unavailable To reconfigure an EP-10 Fuel FlowIf configuration name available Fluid Level menu EP-15 Fluid Level ConfigurationTo configure EP-15 Fluid Level for Fuel To configure EP-15 Fluid Level for Oil To reconfigure EP-15 Fluid Level To unconfigure EP-15 Fluid LevelTo set a Level Warning To execute Reset commandLevel Warning To configure Suzuki Engine Interface Suzuki Engine Interface ConfigurationTo reconfigure a Suzuki Engine Interface To unconfigure a Suzuki Engine InterfaceIf all interfaces configured Configuration name unavailable Fuel Warning Fuel Flow Accuracy Calibrating EP SensorsEP-10 Fuel Flow Calibration To calibrate an EP-10 Fuel Flow Refill TankPartial Fill Reset CalibrationTo execute Reset Calibration command To execute 2-Point calibration EP-15 Fluid Level CalibrationTo execute 3-Point calibration Point CalibrationTo execute 5-Point calibration Engine Interface Accuracy To Reset CalibrationCalibrating Fuel Flow in a Suzuki Engine Interface To calibrate a Suzuki Engine Interface Refill Tank Reset Calibration Calibrating EP-30 Trim Tabs Page Page Page Appendix Page Lowrance Electronics Full ONE-YEAR Warranty Not toll-free How to Obtain Service…Accessory Ordering Information for all countries Visit our web site