Lowrance electronic LMF-200 manual If all interfaces configured Configuration name unavailable

Page 52

If all interfaces configured (Configuration name unavailable):

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight B. DEVICES and press MENU. The Bus Devices list will appear.

3.Select Port Eng and press MENU.

4.Highlight UNSET ENGINE and press MENU. The following message will appear: Hit Menu to Unset Dev Name.

5. Press MENU and you will be taken back to the Bus Devices menu, where engine interface (formerly Port Eng) now will be displayed as UnCfg Eng. Remember: If the engine interface you just unconfigured is not shown on the Bus Devices the list, you will have to refresh the list. Let the Bus Devices list time out then access it again.

6.Highlight STBD ENG and press MENU. Select CHANGE ENGINE and press MENU, which will open the Select Engine menu with up to three options (Port, Center and Starboard), depending on the engine-tank configuration you selected.

7.Highlight PORT and press MENU.

8.You will be taken back to the Bus Devices list, where the engine interface you selected (formerly Stbd Eng) will now be shown as Port Eng. If the newly configured interface is not shown, refresh the Bus Devices list.

9.Now, select UNCFG ENG and press MENU. The following message will appear: Hit Menu to Cfg Eng Int. Press MENU.

10.The Suzuki Engine Model menu will appear with the following options: DF40, DF50, DF60, DF70, DF90/115, DF140, DF150, DF175, DF200/225, DF250 and DF300. Select your engine from the list and press MENU.

11.The Select Engine menu will appear with up to three options: Port, Center and Starboard. Highlight Starboard and press MENU. You will be taken back to the Bus Devices list where the engine interface now will be displayed as Stbd Eng. If the newly configured interface is not shown, refresh the Bus Devices list. (If you have a single-engine configuration, you will not be taken to the Select Engine menu. You will be returned to the Bus Devices list.)

If desired configuration name available:

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight B. DEVICES and press MENU. The Bus Devices list will appear.

46

Image 52

Contents LMF-200 Copyright 2006 Lowrance Electronics, Inc All rights reserved Visit our web siteTable of Contents Backlight Sync BL Sync Iii Page Introduction Page Preparation Recommended Tools and SuppliesInstallation Sequence Mounting the GaugeWiring LMF-200 cable connections Compatibility Connecting to a Nmea 2000 NetworkNetwork Backbone and Network Nodes Adding a Network Node Additional Network Information Menu Commands Understanding this ManualUp and Down keys Menu keyBoat Setup To execute Boat SetupBasic Menu TimeoutPages Viewing Pages Page Screen Rotation OptionsPages Menu To add a page to the display RemoveTo remove a page from the display AutoscrollPop-ups Setup To set a Pop-UpStay Time To set Stay TimeRPM Threshold set up Engine Trim Threshold set upTrim Tabs Threshold set up Pop-up ThresholdsRudder Threshold set up To adjust BacklightScreen BacklightAudio Setup To adjust ContrastContrast Reverse Video Rev VideoSystem Setup Menu To set the Shallow Alarm Sonar AlarmsTo set the Deep Alarm Timeout To reset Eng/Tank configurationReset To reset valuesTo access the Nmea Information screen To access System Information screenNmea Info System InformationTo set Engine Warnings Speed RangeTo set Speed Range Pressure RangeUnits To set Pressure RangeTo change Speed and Distance units To change Temperature units To change Pressure unitsTo change Depth units To change GPS unitsFuel Setup To change Volume unitsRefill Tank Refill T To refill tankTo use Partial Fill Economy Speed Eco spdTo change Economy Speed Source Fuel Remaining Source FRem SrcCustomizing Pages To customize the Single Digital To customize the Dual Digital To Customize the GaugeTo Customize the Fuel Manager To Customize Trim TabsEP-35 Temperature Configuration To configure EP-35 Temp SensorTo reconfigure an EP-35 temp sensor To unconfigure EP-35 temp sensorIf all temps configured Configuration name unavailable EP-10 Fuel Flow Configuration If desired configuration name availableTo configure Fuel Flow To unconfigure an EP-10 Fuel FlowTo reconfigure an EP-10 Fuel Flow If all fuel flows configured Configuration name unavailableIf configuration name available EP-15 Fluid Level Configuration Fluid Level menuTo configure EP-15 Fluid Level for Fuel To configure EP-15 Fluid Level for Oil To unconfigure EP-15 Fluid Level To reconfigure EP-15 Fluid LevelLevel Warning To execute Reset commandTo set a Level Warning Suzuki Engine Interface Configuration To configure Suzuki Engine InterfaceTo unconfigure a Suzuki Engine Interface To reconfigure a Suzuki Engine InterfaceIf all interfaces configured Configuration name unavailable Fuel Warning EP-10 Fuel Flow Calibration Calibrating EP SensorsFuel Flow Accuracy Refill Tank To calibrate an EP-10 Fuel FlowTo execute Reset Calibration command Reset CalibrationPartial Fill EP-15 Fluid Level Calibration To execute 2-Point calibrationPoint Calibration To execute 3-Point calibrationTo execute 5-Point calibration Calibrating Fuel Flow in a Suzuki Engine Interface To Reset CalibrationEngine Interface Accuracy To calibrate a Suzuki Engine Interface Refill Tank Reset Calibration Calibrating EP-30 Trim Tabs Page Page Page Appendix Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Not toll-freeAccessory Ordering Information for all countries Visit our web site