Lowrance electronic LMF-200 manual To configure EP-15 Fluid Level for Fuel

Page 46

To configure EP-15 Fluid Level for Fuel:

1.Make sure the Fuel Remaining Source has been set to Fluid Level. Press MENU, select SYSTEM SETUP and press MENU.

2.Highlight FUEL MNGR (Fuel Manager) and press MENU. Select FREM SRC (Fuel Remaining Source) and press MENU. Highlight FLUID LEVEL and press MENU. You will be taken back to the main display. Now we are ready to configure the sensor.

3.Press MENU, select SYSTEM SETUP and press MENU. Highlight B. DEVICES and press MENU.

4.Select an unconfigured fluid level from the bus devices list and press MENU. The fluid level menu will appear.

5.Highlight FUEL from the list of fluid types and press MENU. If your engine-tank configuration is set for multiple tanks, a menu will appear with up to three options: Port Tank, Cen (Center) Tank and Stbd (Starboard) Tank.

6.Highlight one of the three tank options and press MENU. You will be taken back to the Bus Devices list, where your newly configured Fluid Level will be listed as: F. Tnk (P), F. Tnk (C) or F. Tnk (S), depending on the tank location you chose. If you have one tank, it will be shown as F. Tnk.

To configure EP-15 Fluid Level for Fresh Water:

1.Press MENU, select SYSTEM SETUP and press MENU. Highlight B. DEVICES and press MENU.

2.Select the desired unconfigured fluid level (Unfcg FL) from the Bus Devices list and press MENU, which will launch the following message: Hit Menu to Cfg FLev Sns.

3.Press MENU, select FRESH W from the list of fluid types and press MENU. The Tank Number window will appear.

4.Assign a tank number (1, 2 or 3) to the tank using the fluid level you are configuring and press MENU. That will launch the Tank Size window.

5.Input the capacity of the tank (gallons) and press MENU. You will be directed to the Bus Devices list, where the fluid level you configured will be displayed as FrW Tnk1, FrW Tnk2 or FrW Tnk3, depending on the tank number you assigned it.

To configure EP-15 Fluid Level for Waste Water (Gray Water):

1.Press MENU, select SYSTEM SETUP and press MENU. Highlight B. DEVICES and press MENU.

40

Image 46

Contents LMF-200 Copyright 2006 Lowrance Electronics, Inc All rights reserved Visit our web siteTable of Contents Backlight Sync BL Sync Iii Page Introduction Page Preparation Recommended Tools and SuppliesInstallation Sequence Mounting the GaugeWiring LMF-200 cable connections Compatibility Connecting to a Nmea 2000 NetworkNetwork Backbone and Network Nodes Adding a Network Node Additional Network Information Up and Down keys Menu CommandsUnderstanding this Manual Menu keyBoat Setup To execute Boat SetupBasic Menu TimeoutPages Viewing Pages Page Screen Rotation OptionsPages Menu To remove a page from the display To add a page to the displayRemove AutoscrollStay Time Pop-ups SetupTo set a Pop-Up To set Stay TimeTrim Tabs Threshold set up RPM Threshold set upEngine Trim Threshold set up Pop-up ThresholdsScreen Rudder Threshold set upTo adjust Backlight BacklightContrast Audio SetupTo adjust Contrast Reverse Video Rev VideoSystem Setup Menu To set the Shallow Alarm Sonar AlarmsTo set the Deep Alarm Reset TimeoutTo reset Eng/Tank configuration To reset valuesNmea Info To access the Nmea Information screenTo access System Information screen System InformationTo set Speed Range To set Engine WarningsSpeed Range Pressure RangeUnits To set Pressure RangeTo change Speed and Distance units To change Depth units To change Temperature unitsTo change Pressure units To change GPS unitsRefill Tank Refill T Fuel SetupTo change Volume units To refill tankTo change Economy Speed Source To use Partial FillEconomy Speed Eco spd Fuel Remaining Source FRem SrcCustomizing Pages To customize the Single Digital To customize the Dual Digital To Customize the GaugeTo Customize the Fuel Manager To Customize Trim TabsEP-35 Temperature Configuration To configure EP-35 Temp SensorTo reconfigure an EP-35 temp sensor To unconfigure EP-35 temp sensorIf all temps configured Configuration name unavailable EP-10 Fuel Flow Configuration If desired configuration name availableTo configure Fuel Flow To unconfigure an EP-10 Fuel FlowTo reconfigure an EP-10 Fuel Flow If all fuel flows configured Configuration name unavailableIf configuration name available EP-15 Fluid Level Configuration Fluid Level menuTo configure EP-15 Fluid Level for Fuel To configure EP-15 Fluid Level for Oil To unconfigure EP-15 Fluid Level To reconfigure EP-15 Fluid LevelLevel Warning To execute Reset commandTo set a Level Warning Suzuki Engine Interface Configuration To configure Suzuki Engine InterfaceTo unconfigure a Suzuki Engine Interface To reconfigure a Suzuki Engine InterfaceIf all interfaces configured Configuration name unavailable Fuel Warning EP-10 Fuel Flow Calibration Calibrating EP SensorsFuel Flow Accuracy Refill Tank To calibrate an EP-10 Fuel FlowTo execute Reset Calibration command Reset CalibrationPartial Fill EP-15 Fluid Level Calibration To execute 2-Point calibrationPoint Calibration To execute 3-Point calibrationTo execute 5-Point calibration Calibrating Fuel Flow in a Suzuki Engine Interface To Reset CalibrationEngine Interface Accuracy To calibrate a Suzuki Engine Interface Refill Tank Reset Calibration Calibrating EP-30 Trim Tabs Page Page Page Appendix Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Not toll-freeAccessory Ordering Information for all countries Visit our web site